The URL can be used to link to this page

Home My WebLink AboutE7.00LIGHTING FIXTURE SCHEDULES & CONTROLSSCALE:SCALE:SCALE: LVD LVD LVD LVD TYPICAL CONFERENCE ROOM - LIGHTING CONTROL DIAGRAM6 NONE TYPICAL LAB WRITE-UP - LIGHTING CONTROL DIAGRAM3 NONE TYPICAL SUPPORT EQUIP. ROOM - LIGHTING CONTROL DIAGRAM5 NONE LIGHTING CONTROL RISER DIAGRAM1 NONESCALE: ELECTRICAL CONTRACTOR TO PROVIDE CAT-5 DATA CABLE. SEE CAT-5 REQUIREMENTS SHEET & RJ45 CONNECTOR DETAIL. TEST ALL CABLE LENGTHS AND TERMINATION'S W/CAT-5 TESTER. VOLTAGE CONTROL WIRING TO BE INSTALLED PER NATIONAL ELECTRICAL CODE FOR CLASS-2 LOW VOLTAGE WIRING. ALL LOW VOLTAGE COMMUNICATION CABLE & HARDWIRE LOW FROM LINE VOLTAGE BY A MINIMUM DISTANCE OF 1-FOOT. RUN IN LINE VOLTAGE RACEWAYS. SEPARATE LOW VOLTAGE RUNS CLASS-2 LOW VOLTAGE WIRING SHALL NOT BE MIXED WITH OR CONFIGURATIONS ALLOWED WITHOUT POWER SUPPLY REPEATERS. FROM ONE PANEL OR DEVICE TO THE NEXT. NO "STAR" OR "T" CAT-5 DATA CABLE RUNS TO BE INSTALLED IN A DAISY CHAIN FOR THE INSTALLATION ENVIRONMENT OR CONDITIONS ON SITE. INSTALLED WITH THE APPROPRIATE JACKET TYPE OR CONDUIT ALL CLASS-2 & CAT-5 DATA CABLE RUNS TO BE PROVIDED AND A. B. C. D. E. FOR PROPER SYSTEM OPERATION, BASED ON THE ACTUAL NUMBER ADDITIONAL POWER OR DATA REPEATING DEVICES MAY BE REQ'D AND DISTANCE OF DEVICES TO BE INSTALLED ON CAT-5 DATA LINE. F. G. 2 3 4 5 6 7 8 9 10 1 R1 D1 R2 D2 OUTIN A:F1 N:03 a On/Off Ramp Up Ramp Dn PS-IN 6 8 3 1 1 R1 D1 R2 D2 A:F1 N:04 a On/Off Ramp Up Ramp Dn PS-IN PS-IN OUTIN 1 1 6 8 3 1010 R1 D1 A:F1 N:07 a On/Off Ramp Up Ramp Dn OUTIN 1 1 6 3 10 CAT-5E DATA CABLE NOT USED PHOTOCELL CONTROLLER & REMOTELY MOUNTED SENSOR HEAD. PROVIDE 3-#18 AWG MIN. FROM SENSOR TO CONTROLLER. EMERGENCY POWER AND CONTROL ULO924 BYPASS RELAY LOW VOLTAGE DIMMER STATION DIMMER REMOTE RELAY CAT-5E CONNECTED W/0-10VDC DIMMING CONTROL NOT USED EVO DISTRIBUTED CONTROL PANEL SELECTABLE LIGHTING APPLICATION (A) FOR 16 PRE-PORGRAMMED APPLICATIONS RELAY CONTROL PANEL R40-1,2&3 POLE RELAY AS LISTED. GENERAL NOTES DEVICES MAY COME UNIQUELY PRE-ADDRESSED AND ARE LOCATION SPECIFIC. IT IS THE CONTRACTOR'S RESPONSIBILITY TO PROPERLY LOCATE DEVICES. REFER TO KEY NOTES AND GENERAL NOTES ON THIS SHEET.1.REFER TO KEY NOTES AND GENERAL NOTES ON THIS SHEET.1. REFER TO KEY NOTES AND GENERAL NOTES ON THIS SHEET.1. a 6 b R4 D4 EPC-2 7 KEY NOTES REFER TO KEY NOTES AND GENERAL NOTES ON THIS SHEET.1. Node: 01 OUT Panel OUTIN A:F1 N:02 OUTIN A:F1 N:02 OUTIN A:F1 N:02 OUTIN A:F1 N:02 OUTIN A:F1 N:02 OUTIN A:F1 N:02 2ND FLOOR 3RD FLOOR 1 1 1 1 1 1 1 1 TO NEXT CONTROLLER TO NEXT CONTROLLER 3 3 3 3 3 3 277V 2.RELAY FOR AUTOMATIC RECEPTACLE CONTROL FOR ELECTRIFIED FURNITURE. QUANTITY OF REQUIRED RELAYS SHALL BE DETERMINED BY THE ELECTRICAL CONTRACTOR N THE FIELD. (1) PANEL CAN CONTROL A MAXIMUM OF (2) INDEPENDENT ROOMS. (1) PANEL CAN CONTROL A MAXIMUM OF (2) INDEPENDENT ROOMS.2. (1) PANEL CAN CONTROL A MAXIMUM OF (2) INDEPENDENT ROOMS.2. B SPACE TYPE C SPACE TYPE C SPACE TYPE In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS 2 In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS In:1 Out:1 In:2 Out:2 In:3 Out:3 In:4 Out:4 PS:1 PS:2 Local LS 1 1 5 1 1 1 1 5 5 CEILING MOUNTED MOTION SENSOR 3#18AWG TO 24VDC POWERED INPUT IN PANEL. P1 P1 S2 S2 S1 FLOOR PLAN SYMBOL (TYPICAL) FLOOR PLAN SYMBOL (TYPICAL) A RESEARCH B C WRITE UP CONFERENCE D BREAK OUT AREA SEQUENCE: OVERHEAD LIGHTS ARE TURNED ON MANUALLY VIA A SWITCH. ON: THE LIGHTS ARE MANUALLY TURNED ON. ADJUST:THE LIGHTS ARE CONTROLLED WITH AN ON/OFF DIMMING SWITCH AT THE ENTRANCE. OFF: THE LIGHTS ARE AUTOMATICALLY TURNED OFF OR MANUALLY TOGGLED OFF USING A WALL CONTROL. LIGHTS WILL AUTOMATICALLY TURN OFF AFTER THE SPACE HAS BEEN VACANT FOR 20 MINUTES. E LIGHTING CONTROL INTENT SCHEDULE DIGITAL LIGHTING POWER PACK WITH MANUAL SWITCH, CEILING SENSOR. DIGITAL LIGHTING POWER PACK WITH MANUAL SWITCH, CEILING SENSOR, AND PHOTOCELL PUBLIC RESTROOM DIGITAL LIGHTING POWER PACK WITH MANUAL SWITCH AND CEILING SENSOR SEQUENCE: ALL LIGHTS ARE TURNED ON MANUALLY VIA SWITCH AND MANUALLY TURNED OFF VIA SWITCH OR VACANCY SENSOR. ON: THE LIGHTS ARE MANUALLY TURNED ON. OFF: THE LIGHTS ARE AUTOMATICALLY TURNED OFF OR MANUALLY TOGGLED OFF USING A WALL CONTROL. LIGHTS WILL AUTOMATICALLY TURN OFF AFTER THE SPACE HAS BEEN VACANT FOR 20 MINUTES . DIGITAL LIGHTING POWER PACK WITH MANUAL SWITCH, CEILING SENSOR, AND PHOTOCELL SEQUENCE:EQUIPMENTROOM TYPESPACE TYPE SEQUENCE: MANUAL ON/OFF AND DIMMING ON: THE LIGHTS ARE MANUALLY TURNED ON ADJUST: THE GENERAL ROOM LIGHTING IS ON/OFF CONTROLLED WITH A DIMMING SWITCH AT THE ENTRANCE. THE LIGHTS ARE MANUALLY DIMMED AT THE ENTRANCE TO THE ROOM. OFF: THE LIGHTS ARE AUTOMATICALLY TURNED OFF VIA A VACANCY SENSOR AFTER THE ROOM HAS BEEN VACANT FOR 20 MINUTES OR MANUALLY TOGGLED OFF USING A WALL CONTROL. PHOTO: THE DESIGNATED ROOM LIGHTS DIM BASED ON AVAILABLE DAYLIGHT IN THE ROOM. SET TO MAINTAIN 50 FOOT-CANDLES AT A HEIGHT OF 36 INCHES. SEQUENCE: MANUAL ON/OFF AND DIMMING ON: THE LIGHTS ARE MANUALLY TURNED ON ADJUST: THE GENERAL ROOM LIGHTING IS ON/OFF CONTROLLED WITH DIMMING SWITCH AT THE ENTRANCE. THE LIGHTS ARE MANUALLY DIMMED AT THE ENTRANCE TO THE ROOM. OFF: THE LIGHTS ARE AUTOMATICALLY TURNED OFF VIA VACANCY SENSOR AFTER THE ROOM HAS BEEN VACANT FOR 20 MINUTES OR MANUALLY TOGGLED OFF USING A WALL CONTROL. PHOTO: THE PERIMETER LIGHTS AND 50% OF THE GENERAL ROOM LIGHTS DIM BASED ON AVAILABLE DAYLIGHT IN THE ROOM. SET TO MAINTAIN 50 FOOT-CANDLES AT A HEIGHT OF 36 INCHES. LAB SUPPORT EQUIPMENT ROOMS DIGITAL LIGHTING POWER PACK WITH MANUAL SWITCH, CEILING SENSOR SEQUENCE: MANUAL ON/OFF AND DIMMING ON: THE LIGHTS ARE MANUALLY TURNED ON ADJUST: THE GENERAL ROOM LIGHTING IS ON/OFF CONTROLLED WITH A DIMMING SWITCH AT THE ENTRANCE. THE LIGHTS ARE MANUALLY DIMMED AT THE ENTRANCE TO THE ROOM. OFF: THE LIGHTS ARE AUTOMATICALLY TURNED OFF VIA A VACANCY SENSOR AFTER THE ROOM HAS BEEN VACANT FOR 20 MINUTES OR MANUALLY TOGGLED OFF USING A WALL CONTROL. 2 Architect Payette Associates Architects, P.C. 290 Congress Street, Fifth Floor Boston, MA 02210-1005 Tel: 617-895-1000 Fax: 617-895-1002 MEP/FP Engineer Vanderweil 274 Summer Street Boston, MA 02210 Tel: 617-423-7423 Structural Engineer SGH 41 Seyong Street Building 1, Suite 500 Waltham, MA 02453 Tel: 781-907-9000 Fax: 781-907-9009 Drawing Scale Project Number Date Issued Renovation of Olin Hall for Chemical and Biomolecular Engineering - Phase 1 Code Consultant Hastings Consulting Inc 142 Hanlon Road Hollister, MA 01746 Tel: 508-397-8417 Lighting Designer Available Light 10 Derby Square #3 Salem, MA 01970 Tel: 978-744-6800 N Cost Consultant Dharam Consulting 745 Atlantic Ave Fl 8 Boston, MA 02111 Tel: 617-913-4345 Abatement Specialist Delta 860 Hooper Rd Endwell, NY 13760 Tel: 607-231-6600 Civil Engineer T.G. Miller, P.C. 203 N. Aurora Street Ithaca, NY 14850 Tel: 607-272-6477 N.T.S E7.00 29313.00 11/30/18 LIGHTING FIXTURE SCHEDULES & CONTROLS LIGHTING FIXTURE SCHEDULE TYPE DESCRIPTION MOUNTING MANUFACTURER MODEL DIMMING VOLTAGE TOTAL WATTAGE POWER FACTOR LUMENS OUTPUT COLOR TEMP.LAMP COMMENTS DWA WALL MOUNTED LED LINEAR FIXTURE WALL VODE WG-01-VARIES-WA-12-00-AE-XXX-B-SO-35-BB-19-0-TBD Yes 277 V 57 0.9 6939 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS DWA 4 WALL MOUNTED LED LINEAR FIXTURE WALL VODE WG-01-VARIES-WA-12-00-AE-XXX-B-SO-35-BB-19-0-TBD Yes 277 V 57 0.9 6939 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS DWA 9 WALL MOUNTED LED LINEAR FIXTURE WALL VODE WG-01-VARIES-WA-12-00-AE-XXX-B-SO-35-BB-19-0-TBD Yes 277 V 57 0.9 6939 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS DWB WALL MOUNTED LED VANITY SCONCE WALL EUREKA 3540-23-LED-35-XXX-DV-TBD Yes 277 V 10 0.9 898 lm 35000 K LED SEE ARCHITECTURAL SPECIFICATIONS LPA-10 LINEAR DIRECT/INDIRECT LED PENDANT PENDANT FINELIGHT HP-2-ID-VARIES-B-H-835-F-F-96LG-XXX-DC-FA-TBD Yes 277 V 117 0.9 11080 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS LPB 3 SPOKE DIRECT/INDIRECT LED LINEAR PENDANT PENDANT FLUXWERX PSI-B-D-A-35-TBD-S3-S-E1-XXX-VARIES Yes 277 V 9 0.9 3500 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS LS1 LED LINEAR STRIP PENDANT LAMAR LIGHTING CAL 48 H 35 LENSED Yes 277 V 47 0.9 5040 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS PA CYLINDER LED PENDANT PENDANT GOTHAM LIGHTING ICO-CYL-35/10-2AR-LSS-XXX-UGZ-TBD-DWHG Yes 277 V 13 0.9 1000 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RA LED RECESSED DOWNLIGHT RECESSED GOTHAM LIGHTING ICO-35/10-2AR-LSS-XXX-UGZ-TRW Yes 277 V 13 0.9 1000 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLA 6 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-S-835-F-277-SC-TZ4 Yes 277 V 74 0.9 6576 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLA 8 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-S-835-F-277-SC-TZ4 Yes 277 V 74 0.9 6576 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLA 10 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-S-835-F-277-SC-TZ4 Yes 277 V 92 0.9 8220 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLA 12 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-V-835-F-277-SC-TZ4 Yes 277 V 110 0.9 9864 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLA 16 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-S-835-F-277-SC-TZ4 Yes 277 V 150 0.9 1315 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLB 12 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-B-835-F-277-SC-SF Yes 277 V 55 0.9 5076 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLC-8 LED LINEAR PENDANT PENDANT FINELIGHT HP-4-D-H-835-F-XXX-FA-TBD Yes 277 V 57 0.9 5760 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLC-12 LED LINEAR PENDANT PENDANT FINELIGHT HP-4-D-H-835-F-XXX-FA-TBD Yes 277 V 57 0.9 5760 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLC-22 LED LINEAR PENDANT PENDANT FINELIGHT HP-4-D-H-835-F-XXX-FA-TBD Yes 277 V 57 0.9 5760 lm 3500 K LED SEE ARCHITECTURAL SPECIFICATIONS RLD-8 LINEAR LED RECESSED RECESSED FINELIGHT HP-2R-VARIES-S-835-F-XXX-SC-TZ4 Yes 277 V 29 0.9 2688 lm 3000 K LED SEE ARCHITECTURAL SPECIFICATIONS X1 EXIT SIGN SURFACE No 277 V 2 0.9 LED COORDINATE FACES AND CHEVRONS WITH FLOOR PLANS X2 POLYCARBONATE EXIT SIGN UNIVERSAL COOPER LPX-6 No 277 V 2 0.9 LED COORDINATE FACES AND CHEVRONS WITH FLOOR PLANS. COORDINATE MOUNTING KIT WITH FLOOR PLANS. # DATE DESCRIPTION 1 11/30/18 ISSUED FOR CONSTRUCTION 2 12/18/18 ADDENDUM 01 2 2 DocuSign Envelope ID: BC901AA6-3CDC-45DD-9BA6-B9529CC3D779 12/18/2018