HomeMy WebLinkAboutMP-4013RD FLOOR
0' -0"
ATTIC
10' -4"
BOILER #1
420 MBH
WATER
HEATER
120 MBH
COFFEE URN
(REPLACED WITH
ELECTRIC COFFEE
MAKER)
BOILER #2
420 MBH
1-1/2"
2"
(1473 MBH)
1-1/4"
(399.5 MBH)
(30'-0")
2"
3/4"
1/2"
1"
2"
(960 MBH)
LOWER LEVEL
THIRD FLOOR
RANGE / OVEN /
GRIDDLE
(271.5 MBH)
ATTIC
HMAU-1
128 MBH
1-1/4"3/4"
(VIF)
3/4"
KEF-1
HMAU-1
14ø EA
14ø EA
KEH-1
TEE WITH ACCESS
DOOR
IL-01
1" NG
VENTED EXHAUST FAN
CURB WITH HINGE KIT
AND GREASE CUP
GREASE DUCT
SUPPORT SADDLE.
SECURE TO ROOF
RAFTERS
SECURE 1/2" THREADED RODS
TO L-BRACKETS FASTENED TO
MID-DEPTH OF RAFTERS WITH
1/2”LAG SCREWS (TWO PER
BRACKET).NOTE:
INSTALL NEW FIBERGLASS BATT INSULATION WHERE
DISTURBED BY CONSTRUCTION OPERATIONS.
PROVIDE 8”BATT INSULATION BETWEEN 8”ATTIC
FLOOR FRAMING MEMBERS, PLUS A SECOND LAYER OF
12”FIBERGLASS BATT INSULATION ABOVE AND
PERPENDICULAR TO FRAMING MEMBERS.
1 1/4" NG
EXISTING
EMERGENCY
GAS SHUTT
OFF VALVE
2
MP-401
3RD FLOOR
0' -0"
ATTIC
10' -4"
STAINLESS
STEEL FIELD
WRAP
6' - 8"40x45 OA
PLENUM16x16 SA
FLEX CONNECTION
SECURE UNIT TO
FRAMING WITH
SPRING VIBRATION
ISOLATORS
IL-01
12X12 ACCESS
DOOR
3RD FLOOR
0' -0"
ATTIC
10' -4"6' - 8"12"
7"
4
MP-401
12x8 SA
1" NG
EXISTING EMERGENCY
GAS SHUTOFF VALVE
1 1/4" NG
3/4" NG
TO RANGE
12x12 SA
12x8 SA
12x8 SA
16x16 SA
14ø EA
KEF-1
KEH-1 HOOD CONTROL CABINET
SUPPLY AIR VOLUME DAMPERS
ARE SUPPLIED WITH THE HOOD
VD
SAD-1
550 CFM
SECURE 1/2" THREADED RODS
TO L-BRACKETS FASTENED TO
MID-DEPTH OF RAFTERS WITH
1/2”LAG SCREWS (TWO PER
BRACKET).
VD
EXISTING ANSUL
SYSTEM
ANUL
SYSTEM
PIPING
NOTE:
INSTALL NEW FIBERGLASS BATT
INSULATION WHERE DISTURBED BY
CONSTRUCTION OPERATIONS. PROVIDE 8”
BATT INSULATION BETWEEN 8”ATTIC FLOOR
FRAMING MEMBERS, PLUS A SECOND
LAYER OF 12”FIBERGLASS BATT
INSULATION ABOVE AND PERPENDICULAR
TO FRAMING MEMBERS.SPECIFICATION
THE HOOD FIRE SUPPRESSION SYSTEM SHALL BE THE PRE-ENGINEERED TYPE WITH A FIXED NOZZLE AGENT DISTRIBUTION NETWORK. IT
SHALL BE LISTED WITH UNDERWRITERS LABORATORIES, INC. (UL).
THE REGULATED RELEASE MECHANISM SHALL BE COMPATIBLE WITH A FUSIBLE LINK DETECTION SYSTEM. THE FUSIBLE LINK SHALL BE
SELECTED AND INSTALLED ACCORDING TO THE OPERATING TEMPERATURE IN THE VENTILATING SYSTEM. THE FUSIBLE LINK SHALL BE
SUPPORTED BY A DETECTOR BRACKET/ LINKAGE ASSEMBLY.
FIELD NOTES
-FIELD PIPE DROPS AS SHOWN SLEEVING, ELBOWS, TEES, AND NOZZLES SUPPLIED BY HOOD MANUFACTURER.
-RELOCATE NOZZLES IF FLOW PATTERN IS BLOCKED BY SHELVING, SALAMANDERS, ETC.
-MAXIMUM 9 ELBOWS IN SUPPLY LINE.
-MINIMUM 72 INCHES OF AGENT LINE FROM TANK TO FIRST NOZZLE.
-PRE-PIPED CHARBROILER DROPS ARE SHIPPED LOOSE.
-FACTORY PIPING EXTENDS A MAXIMUM OF 6" ABOVE THE TOP OF THE HOOD.
-THIS FIRE SYSTEM COMPLIES WITH U.L. 300 REQUIREMENTS
DETECTORS
DETECTION LINE
(INSTALLED IN FIELD)
DUCT PROTECTION NOZZLE
APPLIANCE PROTECTION NOZZLE
PLENUM PROTECTION NOZZLE
EXISTING PULL STATION TO REMAIN
EXISTING HOOD FIRE SUPRESSION SYSTEM
NOTE:
HOOD DETAIL IS DIAGRAMMATIC IN NATURE,
ACTUAL NOZZLE QUANTITY MAY DIFFER. HOOD
FIRE SUPPRESSION SYSTEM SHALL BE PIPED AT
THE FACTORY AND READY FOR FIELD CONNECTION
TO EXISTING FIRE SUPPRESSION SYSTEM.
ANUSL SYSTEM PIPING
(FIELD INSTALLED)
6' 0"Nom./6' 0.00"OD
7'-0.00" Overall Length
48"
12"
12"
19"
6"
8"
46"
6"
8"
24"
3"
36"36"
11"
∅14"
U.L. LISTED RECESSED ROUND
LED FIXTURE AND LED LIGHT
SECTION VIEW
FANSLIGHTS
LCD SCREEN
FAN & LIGHT BUTTONS
ROOM TEMP SENSOR
FIELD INSTALLED IN
KITCHEN. REFER TO
PLANS FOR LOCATION
TEMP
SENSOREXISTING
WALL-MOUNTED
ANSUL SYSTEM
3" INTERNAL
STANDOFF
GREASE DRAIN
WITH REMOVABLE
CUP
EXHAUST RISER
HANGING ANGLE
RECESSED ALLANSON ROUND LED FIXTURE AND
LED LIGHT, 3500 K WARM OUTPUT.
23.5% OPEN STAINLESS
STEEL PERFORATED
PANEL
ATTACHING PLATES
SUPPLY RISER WITH VOLUME DAMPER
6"
2 3/4"
12"
18"
FIELD WRAPPER
1" LAYER OF INSULATION FACTORY INSTALLED
ON TOP OF HOOD. MEETS 0 INCH REQUIREMENTS FOR
CLEARANCE TO COMBUSTIBLE SURFACES
EXISTING
EQUIPMENT
48.0" MAX
24" NOM.
48"
GREASE FILTERS
1" LAYER OF INSULATION FACTORY INSTALLED IN
INTERNAL BACK STANDOFF AND TOP OF HOOD.
MEETS 0 INCH REQUIREMENTS FOR CLEARANCE TO
COMBUSTIBLE SURFACES.
24"
UTILITY CABINET
PLAN VIEW
HOOD CORNER
HANGING ANGLE
(WEIGHT BEARING
ANCHOR POINT
FOR HOOD)
1/2" -13 TPI
STEEL ALL-THREAD
1/2" STEEL
FLAT WASHER TOP
& BOTTOM
1/2" -13 TPI
STEEL HEX NUT
1/2" -13 TPI
STEEL HEX NUTS
1/2" STEEL FLAT
WASHER
HOOD CORNER HANGING ANGLE
(HARDWARE BY INSTALLER)
NOTE:
ALL HARDWARE SHALL BE
GRADE 5 (MINIMUM).
1/2" -13 TPI
STEEL HEX NUTS
ASSEMBLY INSTRUCTIONS
HANGING ANGLE MUST BE SUPPORTED WITH 1/2" -13 TPI
GRADE 5 (MINIMUM) ALL-THREAD. SANDWICH HANGING
ANGLES AND CEILING ANCHOR POINTS WITH 1/2" GRADE 5
(MINIMUM) STEEL FLAT WASHERS AND 1/2" -13 TPI GRADE 5
(MINIMUM) HEX NUTS AS SHOWN. MUST USE DOUBLED HEX
NUT CONFIGURATION BENEATH HOOD HANGING ANGLES AND
ABOVE CEILING ANCHORS. MAINTAIN 1/4" OF EXPOSED
THREADS BENEATH BOTTOM HEX NUT. TORQUE ALL HEX
NUTS TO 57 FT-LBS.
SYSTEM CONTROLLER
(KEH-1, KEF-1, HMAU-1, & ALARM)CORNE LL U N IV
E
R
SI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
PHI SIGMA SIGMA, 14 SOUTH AVE
KITCHEN HOOD
EXHAUST
RENOVATION
MP-401
11191594
DETAILS AND
ISOMETRICS
P. OCKENFELS
PCO
4724
JULY 15, 2019
0 2 4 8
SCALE: 1/4"=1'-0"
SCALE: NO SCALE
3 NATURAL GAS PIPING SCHEMATIC
SCALE: NO SCALE
1 KITCHEN EXHAUST SYSTEM ISOMETRIC
SCALE:1/4" = 1'-0"4 KITCHEN SECTION 2
SCALE:1/4" = 1'-0"2 KITCHEN SECTION 1
SCALE: NO SCALE
6 KITCHEN HOOD FIRE SUPRESSION DETAIL
SCALE: NO SCALE
5 KITCHEN EXHAUST HOOD DETAILS
1 5/31/19 ISSUE FOR 50% REVIEW
2 7/10/19 ISSUE FOR COORDINATED REVIEW
3 7/15/19 ISSUE FOR CONSTRUCTION