Loading...
HomeMy WebLinkAbout08 14 16 - Flush Wood DoorsBEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 1 OF 6 NOVEMBER 2, 2012 SECTION 081416 FLUSH WOOD DOORS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Solidcore doors with woodveneer faces. 2. Factory finished flush wood doors. 3. Factory fitting flush wood doors to frames and factory machining for hardware. 1.3 SUBMITTALS A. Product Data: For each type of door indicated. Include details of core and edge construction and trim for openings. B. Shop Drawings: Indicate location, size, and hand of each door; elevation of each kind of door; construction details not covered in Product Data; location and extent of hardware blocking; and other pertinent data. 1. Indicate dimensions and locations of mortises and holes for hardware. 2. Indicate dimensions and locations of cutouts. 3. Indicate requirements for veneer matching. 4. Indicate doors to be factory finished and finish requirements. 5. Indicate fireprotection ratings for firerated doors. C. Samples for Verification: 1. Factory finishes applied to actual door face materials, approximately 8 by 10 inches (200 by 250 mm), for each material and finish. 2. Corner sections of doors, approximately 8 by 10 inches (200 by 250 mm), with door faces and edges representing actual materials to be used. a. Provide samples for each species of veneer and solid lumber required. b. Provide samples for each color, texture, and pattern of plastic laminate required. c. Finish veneerfaced door samples with same mater ials proposed for factoryfinished doors. BEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 2 OF 6 NOVEMBER 2, 2012 D. Warranty: Sample of special warranty. 1.4 QUALITY ASSURANCE A. Quality Standard: In addition to requirements specified, comply with WDMA I.S.1A, "Architectural Wood Flush Doors." 1. Provide WICertified Compliance Certificate indi cating that doors comply with requirements of grades specified. 2. Provide WICertified Compliance Certificate for installation. B. FireRated Wood Doors: Doors complying with NFP A 80 that are listed and labeled by a qualified testing agency, for firepro tection ratings indicated, based on testing at positive pressure according to UL 10C. 1.5 DELIVERY, STORAGE, AND HANDLING A. Comply with requirements of referenced standard and manufacturer's written instructions. B. Package doors individually in plastic bags or cardboard cartons. 1.6 WARRANTY A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace doors that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Warping (bow, cup, or twist) more than 1/4 inch (6.4 mm) in a 42by 84inch (1067by2134mm) section. b. Telegraphing of core construction in face veneers exceeding 0.01 inch in a 3inch (0.25 mm in a 76.2mm) span. 2. Warranty shall also include installation and finishing that may be required due to repair or replacement of defective doors. 3. Warranty Period for SolidCore Interior Doors: Life of installation. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: BEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 3 OF 6 NOVEMBER 2, 2012 1. Algoma Hardwoods, Inc. 2. Marshfield Door Systems, Inc. 2.2 DOOR CONSTRUCTION, GENERAL A. WDMA I.S.1A Performance Grade: Heavy Duty. B. FireProtectionRated Doors: Provide core speci fied or mineral core as needed to provide fireprotection rating indicated on drawings. 1. Edge Construction: Provide edge construction with intumescent seals concealed by outer stile. Comply with specified requirements for exposed edges. 2.3 VENEEREDFACED DOORS FOR TRANSPARENT FINISH A. Interior SolidCore Doors: 1. Grade: Custom (Grade A faces). 2. Species: White oak. 3. Cut: Rotary cut. 4. Core: Particleboard. 5. Construction: Five plies. Stiles and rails are bonded to core, then entire unit abrasive planed before veneering. 6. WDMA I.S.1A Performance Grade: Heavy Duty. 2.4 FABRICATION A. Factory fit doors to suit frameopening sizes in dicated. Comply with clearance requirements of referenced quality standard for fitting unless otherwise indicated. 1. Comply with requirements in NFPA 80 for firerat ed doors. B. Factory machine doors for hardware that is not surface applied. Locate hardware to comply with DHIWDHS3. Comply with fi nal hardware schedules, door frame Shop Drawings, DHI A115W ser ies standards, and hardware templates. 1. Coordinate with hardware mortises in metal frames to verify dimensions and alignment before factory machining. 2.5 SHOP PRIMING A. Doors for Transparent Finish: Shop prime doors with stain (if required), other required pretreatments, and first coat of finish as specified. Seal all four edges, edges of cutouts, and mortises with first coat of finish. BEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 4 OF 6 NOVEMBER 2, 2012 2.6 FACTORY FINISHING A. General: Comply with referenced quality standard for factory finishing. Complete fabrication, including fitting doors for openings and machining for hardware that is not surface applied, before finishing. 1. Finish faces, all four edges, edges of cutouts, and mortises. Stains and fillers may be omitted on bottom edges, edges of cutouts, and mortises. B. Finish doors at factory that are indicated to receive transparent finish. C. Transparent Finish: 1. Grade: Premium. 2. Finish: WI System 5 catalyzed polyurethane. 3. Staining: As selected by Architect from manufacturer's full range. 4. Effect: Semifilled finish, produced by applyin g an additional finish coat to partially fill the wood pores. 5. Sheen: Satin. PART 3 EXECUTION 3.1 EXAMINATION A. Examine doors and installed door frames before hanging doors. 1. Verify that frames comply with indicated requirements for type, size, location, and swing characteristics and have been installed with level heads and plumb jambs. 2. Reject doors with defects. B. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 INSTALLATION A. Hardware: For installation, see Division 08 Section "Door Hardware." B. Installation Instructions: Install doors to comply with manufacturer's written instructions and the referenced quality standard, and as indicated. 1. Install firerated doors in corresponding firer ated frames according to NFPA 80. C. FactoryFitted Doors: Align in frames for unifo rm clearance at each edge. D. FactoryFinished Doors: Restore finish before i nstallation if fitting or machining is required at Project site. BEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 5 OF 6 NOVEMBER 2, 2012 3.3 ADJUSTING A. Operation: Rehang or replace doors that do not swing or operate freely. B. Finished Doors: Replace doors that are damaged or that do not comply with requirements. Doors may be repaired or refinished if work complies with requirements and shows no evidence of repair or refinishing. END OF SECTION 081416 BEARDSLEY DESIGN ASSOCIATES CORNELL – NCP FLUSH WOOD DOORS STANDARD SPECIFICATIONS 08 14 16 PAGE 6 OF 6 NOVEMBER 2, 2012 [ PAGE LEFT INTENTIONALLY BLANK ]