HomeMy WebLinkAbout08 14 16 - Flush Wood DoorsBEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 1 OF 6
NOVEMBER 2, 2012
SECTION 081416 FLUSH WOOD DOORS
PART 1 GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and
Supplementary Conditions and Division 01 Specification Sections, apply to
this Section.
1.2 SUMMARY
A. Section Includes:
1. Solidcore doors with woodveneer faces.
2. Factory finished flush wood doors.
3. Factory fitting flush wood doors to frames and factory machining for
hardware.
1.3 SUBMITTALS
A. Product Data: For each type of door indicated. Include details of core and
edge construction and trim for openings.
B. Shop Drawings: Indicate location, size, and hand of each door; elevation of
each kind of door; construction details not covered in Product Data; location
and extent of hardware blocking; and other pertinent data.
1. Indicate dimensions and locations of mortises and holes for hardware.
2. Indicate dimensions and locations of cutouts.
3. Indicate requirements for veneer matching.
4. Indicate doors to be factory finished and finish requirements.
5. Indicate fireprotection ratings for firerated doors.
C. Samples for Verification:
1. Factory finishes applied to actual door face materials, approximately 8 by
10 inches (200 by 250 mm), for each material and finish.
2. Corner sections of doors, approximately 8 by 10 inches (200 by 250 mm),
with door faces and edges representing actual materials to be used.
a. Provide samples for each species of veneer and solid lumber
required.
b. Provide samples for each color, texture, and pattern of plastic
laminate required.
c. Finish veneerfaced door samples with same mater ials proposed for
factoryfinished doors.
BEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 2 OF 6
NOVEMBER 2, 2012
D. Warranty: Sample of special warranty.
1.4 QUALITY ASSURANCE
A. Quality Standard: In addition to requirements specified, comply with
WDMA I.S.1A, "Architectural Wood Flush Doors."
1. Provide WICertified Compliance Certificate indi cating that doors comply
with requirements of grades specified.
2. Provide WICertified Compliance Certificate for installation.
B. FireRated Wood Doors: Doors complying with NFP A 80 that are listed and
labeled by a qualified testing agency, for firepro tection ratings indicated,
based on testing at positive pressure according to UL 10C.
1.5 DELIVERY, STORAGE, AND HANDLING
A. Comply with requirements of referenced standard and manufacturer's written
instructions.
B. Package doors individually in plastic bags or cardboard cartons.
1.6 WARRANTY
A. Special Warranty: Manufacturer's standard form in which manufacturer
agrees to repair or replace doors that fail in materials or workmanship within
specified warranty period.
1. Failures include, but are not limited to, the following:
a. Warping (bow, cup, or twist) more than 1/4 inch (6.4 mm) in a 42by
84inch (1067by2134mm) section.
b. Telegraphing of core construction in face veneers exceeding 0.01 inch
in a 3inch (0.25 mm in a 76.2mm) span.
2. Warranty shall also include installation and finishing that may be required
due to repair or replacement of defective doors.
3. Warranty Period for SolidCore Interior Doors: Life of installation.
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Manufacturers: Subject to compliance with requirements, available
manufacturers offering products that may be incorporated into the Work
include, but are not limited to, the following:
BEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 3 OF 6
NOVEMBER 2, 2012
1. Algoma Hardwoods, Inc.
2. Marshfield Door Systems, Inc.
2.2 DOOR CONSTRUCTION, GENERAL
A. WDMA I.S.1A Performance Grade: Heavy Duty.
B. FireProtectionRated Doors: Provide core speci fied or mineral core as
needed to provide fireprotection rating indicated on drawings.
1. Edge Construction: Provide edge construction with intumescent seals
concealed by outer stile. Comply with specified requirements for exposed
edges.
2.3 VENEEREDFACED DOORS FOR TRANSPARENT FINISH
A. Interior SolidCore Doors:
1. Grade: Custom (Grade A faces).
2. Species: White oak.
3. Cut: Rotary cut.
4. Core: Particleboard.
5. Construction: Five plies. Stiles and rails are bonded to core, then
entire unit abrasive planed before veneering.
6. WDMA I.S.1A Performance Grade: Heavy Duty.
2.4 FABRICATION
A. Factory fit doors to suit frameopening sizes in dicated. Comply with
clearance requirements of referenced quality standard for fitting unless
otherwise indicated.
1. Comply with requirements in NFPA 80 for firerat ed doors.
B. Factory machine doors for hardware that is not surface applied. Locate
hardware to comply with DHIWDHS3. Comply with fi nal hardware
schedules, door frame Shop Drawings, DHI A115W ser ies standards, and
hardware templates.
1. Coordinate with hardware mortises in metal frames to verify dimensions
and alignment before factory machining.
2.5 SHOP PRIMING
A. Doors for Transparent Finish: Shop prime doors with stain (if required), other
required pretreatments, and first coat of finish as specified. Seal all four
edges, edges of cutouts, and mortises with first coat of finish.
BEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 4 OF 6
NOVEMBER 2, 2012
2.6 FACTORY FINISHING
A. General: Comply with referenced quality standard for factory finishing.
Complete fabrication, including fitting doors for openings and machining for
hardware that is not surface applied, before finishing.
1. Finish faces, all four edges, edges of cutouts, and mortises. Stains
and fillers may be omitted on bottom edges, edges of cutouts, and
mortises.
B. Finish doors at factory that are indicated to receive transparent finish.
C. Transparent Finish:
1. Grade: Premium.
2. Finish: WI System 5 catalyzed polyurethane.
3. Staining: As selected by Architect from manufacturer's full range.
4. Effect: Semifilled finish, produced by applyin g an additional finish coat to
partially fill the wood pores.
5. Sheen: Satin.
PART 3 EXECUTION
3.1 EXAMINATION
A. Examine doors and installed door frames before hanging doors.
1. Verify that frames comply with indicated requirements for type, size,
location, and swing characteristics and have been installed with level
heads and plumb jambs.
2. Reject doors with defects.
B. Proceed with installation only after unsatisfactory conditions have been
corrected.
3.2 INSTALLATION
A. Hardware: For installation, see Division 08 Section "Door Hardware."
B. Installation Instructions: Install doors to comply with manufacturer's written
instructions and the referenced quality standard, and as indicated.
1. Install firerated doors in corresponding firer ated frames according to
NFPA 80.
C. FactoryFitted Doors: Align in frames for unifo rm clearance at each edge.
D. FactoryFinished Doors: Restore finish before i nstallation if fitting or
machining is required at Project site.
BEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 5 OF 6
NOVEMBER 2, 2012
3.3 ADJUSTING
A. Operation: Rehang or replace doors that do not swing or operate freely.
B. Finished Doors: Replace doors that are damaged or that do not comply with
requirements. Doors may be repaired or refinished if work complies with
requirements and shows no evidence of repair or refinishing.
END OF SECTION 081416
BEARDSLEY DESIGN ASSOCIATES
CORNELL – NCP FLUSH WOOD DOORS
STANDARD SPECIFICATIONS 08 14 16 PAGE 6 OF 6
NOVEMBER 2, 2012
[ PAGE LEFT INTENTIONALLY BLANK ]