HomeMy WebLinkAboutDrawings_Baker Complex Kitchen RenovationsCB
FP
UPDNUPDNUPUPUP
UP
UP
UP BAKER TOWER3004TBAKER SOUTH 3004SFOUNDERS HALL 3005BAKER NORTH 3004NBOLDT HALL 3006
WEST AVEUNIVERSITY AVE
ALICE COOK
HOUSE 3031
CARL BECKER
HOUSE 3032
STEWART AVEAREA OF WORK
FLORA ROSE
HOUSE 3035
MENNEN HALL 3014LYON HALL
3011
BAKER TOWER -BASEMENT BAKER NORTH -GROUND FLOOR BAKER SOUTH -GROUND FLOOR
AREA OF WORK AREA OF WORK
B09
B08
G09
G10
G09
G10
T-000 TITLE SHEET
ARCHITECTURAL
A-000 GENERAL NOTES, SYMBOLOGY, AND ABBREVIATIONS
A-101 BAKER TOWER KITCHEN DEMOLITION AND RENOVATION PLANS
A-102 BAKER NORTH KITCHEN DEMOLITION AND RENOVATION PLANS
A-103 BAKER SOUTH KITCHEN DEMOLITION AND RENOVATION PLANS
MECHANICAL/ PLUMBING/ FIRE PROTECTION
MP-001 GENERAL NOTES, SCHEDULES, AND SYMBOL LEGENDS
MP-101 BAKER TOWER PARTIAL FLOOR PLANS
MP-102 BAKER NORTH AND SOUTH GROUND FLOOR PARTIAL HVAC FLOOR PLANS
MP-103 BAKER NORTH AND SOUTH GROUND FLOOR PARTIAL PLUMBING FLOOR PLANS
ELECTRICAL
E-001 GENERAL NOTES AND SYMBOL LEGENDS
E-101 ELECTRICAL REMOVAL PLANS
E-102 ELECTRICAL INSTALLATION PLANS
E-501 PANEL SCHEDULESCORNE
LL U N I V
E
R
SI
TYFOUN
D E D 5681
AD CORNE
LL U N I V
E
RSI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
Cornell University
BAKER TOWER/ NORTH/ SOUTH
BAKER COMPLEX
KITCHEN
RENOVATIONS
T-000
11121224
TITLE SHEET
FE DESIGN
JGC
3004
DECEMBER 17, 2018
BAKER COMPLEX KITCHEN RENOVATIONS
BUILDING CODE SUMMARYGENERAL SYMBOLS LEGEND
EXTERIOR ELEVATION
1
1
1 1X-100
X-100
1
1
1 1 INTERIOR ELEVATION
1
X-100
SECTION MARKER
1
X-100
ENLARGED DETAIL
CONSTRUCTION KEYED NOTE
DEMOLITION KEYED NOTE
DRAWING REVISION NOTE#
DRAWING INDEX
LINETYPE: TO BE PROVIDED / NEW
LINETYPE: DEMOLITION / TO BE RELOCATED
LINETYPE: EXISTING TO REMAIN
PROJECT SCOPE
PERSPECTIVE VIEW -BAKER NORTH
#
#
KEY PLANS -BAKER TOWER, BAKER NORTH, BAKER SOUTH
SITE LOCATION -BAKER COMPLEX
APPLICABLE CODES
2015 (EXISTING) IBC (ADOPTED BY NEW YORK STATE)
PROJECT SUMMARY
THIS PROJECT INCLUDES THE RENOVATION OF 100 SF OF KITCHENS IN
BAKER TOWER, BAKER NORTH, AND BAKER SOUTH. THE WORK IS
ALTERATION LEVEL 2.
BUILDING LIMITATIONS
CONSTRUCTION CLASSIFICATION:2A
CLASSIFICATION OF HAZARDS:NONE
HIGH-RISE BUILDING:NO
EXTINGUISHING REQUIREMENT:THE EXISTING BUILDINGS
ARE SPRINKLERED
OCCUPANCY
OCCUPANCY CLASSIFICATION:RESIDENTIAL (R-2)
THE PURPOSE OF THIS PROJECT IS TO RENOVATE THREE KITCHENS LOCATED INSIDE OF BAKER COMPLEX 3004. WORK INCLUDES NEW FLOOR FINISHES,
PAINT, CABINETS, COUNTERTOPS, AND APPLIANCES (BY OWNER). ALSO, INCLUDED IS NEW PLUMBING FIXTURES AND UPGRADED ELECTRICAL. THE
LOUNGE AT BAKER TOWER WILL RECIEVE NEW FLOOR FINISH, PAINT, AND COUNTERTOP.
1 10/11/18 ISSUE FOR DD REVIEW
2 11/12/18 ISSUE FOR 95% REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
101
A101
1
1
1 1
0
Name
Elevation
101
X-X
X
1t
DN
WALL -EXISTING
WALL -METAL STUD/ GWB
WALL -CONCRETE
WALL -CMU
WALL -BRICK
ITEMS FOR DEMOLITION
DOOR/ WALL -EXISTING
DOOR/ WALL -NEW
DOOR/ WALL -DEMOLITION
TAG -DOOR
TAG -WINDOW
TAG -WALL
TAG -ROOM #
CENTER LINE
PHOTO REFERENCE
LEVEL MARKER
COLUMN GRID MARKER
ELEVATION MARKER
UP
ELEVATION CHANGE ARROWS
BREAK LINE
SYMBOLS
0' -0"
ABBREVIATIONS
A
&AND
@ AT
ACT ACOUSTICAL CEILING TILE
ALT ALTERNATE
ALUM ALUMINUM
AVG AVERAGE
AFF ABOVE FINISH FLOOR
B
BD BOARD
BLDG BUILDING
BOD BOTTOM OF DECK
BSMT BASEMENT
C
CG CORNER GUARDS
CJ CONTROL JOINT
CLG CEILING
CL CENTER LINE
CLR CLEAR
CMU CONCRETE MASONRY UNIT
COL COLUMN
CONC CONCRETE
CONF CONFERENCE
CONT CONTINUOUS
CORR CORRIDOR
CPT CARPET
CRS COURSE(S)
CT CERAMIC TILE
D
DEMO DEMOLITION
DF DRINKING FOUNTAIN
DIA DIAMETER
DIM DIMENSION
DN DOWN
DO DOOR OPENING
DWG DRAWING
E
EA EACH
EJ EXPANSION JOINT
ELEC ELECTRIC
ELEV ELEVATION/ ELEVATOR
EPDM RUBBER ROOF MEMBRANE
EQ EQUAL
EX'G EXISTING
EXT EXTERIOR
F
FD FLOOR DRAIN
FDN FOUNDATION
FEC FIRE EXTINGUISHER CABINET
FFE FINISH FLOOR ELEVATION
FRP FIBER REINFORCED POLYESTER
FT FOOT/FEET
FTG FOOTING
G
GA GAGE
GALV GALVANIZED
GC GENERAL CONTRACTOR
GEN GENERAL
GL GLASS
GWB GYPSUM WALL BOARD
H
HC HANDICAPPED
HT HEIGHT
HM HOLLOW METAL
HR HOUR
HVAC HEATING, VENTILATING & AC
J
JAN JANITOR
L
LAV LAVATORY
LB/#POUND
LGMF LIGHT GAGE METAL FRAMING
M
MFR MANUFACTURER
MAT MATERIAL
MAX MAXIMUM
MEZZ MEZZANINE
MIN MINIMUM
MO MASONRY OPENING
MTL METAL
N
NA NOT APPLICABLE
NIC NOT IN CONTRACT
NR NOT RATED
NTS NOT TO SCALE
O
OC ON CENTER
OD OUTSIDE DIAMETER
OPNG OPENING
OSB ORIENTER STRAND BOARD
P
+/-PLUS OR MINUS
PSF POUNDS PER SQUARE FOOT
PSI POUNDS PER SQUARE INCH
PT PRESSURE TREATED
Q
QTY QUANTITY
R
R RISER
RD ROOF DRAIN
REF REFRIGERATOR
REQ REQUIRED
REV REVISION
RO ROUGH OPENING
RTU ROOF TOP UNIT
S
SHTG SHEATHING
SIM SIMILAR
SF SQUARE FOOT/ FEET
SS STAINLESS STEEL
STL STEEL
STD STANDARD
T
T TREAD
T&G TONGUE & GROOVE
TEL TELEPHONE
TEMP TEMPERATURE
TOS TOP OF STEEL
TV TELEVISION
TYP TYPICAL
U
UEV UNEVEN DOORS W/ VISION PANEL
UEF UNEVEN FLUSH DOOR
V
VCT VINYL COMPOSITION TILE
VIF VERIFY IN FIELD
W
W/O WITHOUT
WD WOOD CORNE
LL U N I V
E
RSI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER TOWER/ NORTH/ SOUTH
BAKER COMPLEX
KITCHEN
RENOVATIONS
A-000
11121224
GENERAL
NOTES,
SYMBOLOGY,
AND
ABBREVIATIONS
J. COOLBAUGH
JGC
3004
DECEMBER 17, 2018
SCOPE OF WORK
1.0 REMOVE EXISTING CABINETS AND COUNTERTOP AND REPLACE WITH NEW ONES.
2.0 PROVIDE NEW WALL AND FLOOR FINISHES.
3.0 MODIFY EXISTING MABLE AROUND THE EXISTING WINDOW AND ADD WOOD TRIM.
4.0 INSTALL NEW OWNER SUPPLIED APPLIANCES.
GENERAL NOTES
1.0 DESIGN, CONSTRUCTION AND SAFETY SHALL CONFORM TO ALL LOCAL, STATE AND
OWNER SPECIFIC CODES, INCLUDING (BUT NOT LIMITED TO) THE NEW YORK STATE
UNIFORM FIRE PROTECTION AND BUILDING CODE, LATEST REVISION, THE NFPA 101
LIFE SAFETY CODE, LATEST REVISION, ANSI A117.1 - LATEST REVISION, OSHA, AND
ANY OTHER CODES GOVERNED BY THE JURISDICTION IN WHICH THIS PROJECT IS
BEING CONSTRUCTED.
2.0 THIS CONTRACT REQUIRES COMPLETE, FINISHED WORKABLE PROJECT OF THE
AREAS INDICATED BY THE CONTRACT DOCUMENTS, AND SHALL INCLUDE ALL
MATERIALS AND LABOR NECESSARY TO COMPLETE, REGARDLESS OF WHETHER OR
NOT ALL WORK OR EACH ITEM IS SPECIFICALLY INDICATED ON ANY OTHER
PORTION OF THE DRAWINGS AND / OR NOTES.
3.0 WHERE MATERIALS REFERENCED ON DRAWINGS, OR NECESSARY TO COMPLETE
THE WORK OF THIS CONTRACT ARE NOT SPECIFIED HEREIN, PROVIDE BEST
QUALITY MATERIALS. WHERE MATERIALS ARE INTENDED TO MATCH EXISTING,
PROVIDE CLOSEST POSSIBLE MATCH, SUBJECT TO OWNER'S APPROVAL. ALL ITEMS
AND WORK ON DRAWINGS ARE NEW, UNLESS INDICATED EXISTING. ALL WORK
WHICH HAS BEEN DAMAGED SHALL BE REPAIRED OR REPLACED AT NO COST TO
THE OWNER. WHERE ITEMS CAN NOT BE REPAIRED TO A ""NEW CONDITION"", OR
WHERE THE STRUCTURAL INTEGRITY HAS BEEN AFFECTED, ITEMS SHALL BE
REPLACED AT NO COST TO THE OWNER.
4.0 CONTRACTOR IS RESPONSIBLE TO VERIFY ALL SITE, FIELD AND BUILDING
CONDITIONS PRIOR TO SUBMITTING BIDS AND COMMENCING WORK. IF THERE ARE
ANY DISCREPANCIES BETWEEN DRAWINGS AND FIELD CONDITIONS, NOTIFY THE
PROJECT MANAGER, WHO WILL REQUEST CLARIFICATION FROM THE
ARCHITECT/ENGINEER AND PROVIDE CLARIFICATION IN WRITING.
5.0 WHERE EXISTING CONSTRUCTION OR ITEMS HAVE BEEN INFILLED, REMOVED AND /
OR DISTURBED FOR INSTALLATION OF NEW WORK, CAUSING THE EXPOSURE OF
UNFINISHED AND/OR DAMAGED SURFACES RESULTING SURFACES AND INFILLED
SURFACES SHALL BE RECONSTRUCTED WITH MATERIALS TO MATCH FINISHED
AREAS. ALL ABANDONED OPENINGS (i.e. DUCT/PIPE REMOVALS, ETC.) AT WALLS,
ROOF OR FLOOR TO BE INFILLED SOLID.
6.0 WORK IS REQUIRED IN VARIOUS PORTIONS OF THE FACILITY TO EXECUTE WORK OF
OTHER TRADES (i.e. ELECTRICAL, MECHANICAL). ALTHOUGH NOT NECESSARILY
SHOWN ON DRAWINGS, WORK IS REQUIRED IN THESE AREAS CONSISTING OF
REMOVAL / REPLACEMENT OF CEILINGS, WALLS, FINISHES, PAVEMENT AND OTHER
CONSTRUCTION AS NECESSARY TO PERFORM WORK AND RESTORE THESE
SPACES OR AREAS TO ORIGINAL CONDITION.
7.0 GENERAL CONTRACTOR IS TO COORDINATE WORK OF ALL TRADES. SCHEDULE
WORK PROGRESS THROUGHOUT THE ENTIRE PROJECT TO PREVENT CONFLICTS
AND INTERFERENCES. OBTAIN ALL NECESSARY INFORMATION SUCH AS SIZES,
LOCATIONS, TEMPLATES, LAYOUT, DIMENSIONS AND ALL OTHER INFORMATION
NECESSARY FOR A PROPER AND WELL COORDINATED INSTALLATION. PRIOR TO
INSTALLATION OF ITEMS, VERIFY AND CONFIRM WITH EACH CONTRACTOR EXACT
LOCATION OF ALL ITEMS.
8.0 ALL PENETRATIONS (EXISTING OR NEW) THROUGH FLOORS AND FULL HEIGHT
WALLS - IN AREA OF WORK TO BE FIRE STOPPED. ALL GAPS AND JOINTS AT RATED
FLOORS, ROOFS AND WALLS TO BE FIRE & SMOKE STOPPED. GAPS AND JOINTS
INCLUDE (BUT ARE NOT LIMITED TO) TOP OF WALL TO FLOOR OR ROOF DECK, WALL
TO BEAMS, AND CONTROL OR EXPANSION JOINTS. FIRE STOPPING INCLUDES BOTH
FORM OR PACKING MATERIAL AND THE FILL, VOID OR CAVITY MATERIAL. PROVIDE
AND INSTALL LABELING REQUIRED BY CODE. LABELS SHALL INCLUDE
PENETRATION TYPE WITH UL LISTING USED, MATERIAL USED, DATE INSTALL AND
NAME OF INSTALLER.
9.0 JOBSITE WILL BE CLEANED DAILY AND DEBRIS REMOVED TO CONTAINERS OR TO
VEHICLE WHICH WILL REMOVE DEBRIS FROM CAMPUS. CONTAINERS WILL BE
REMOVED AS SOON AS FULL OR WHEN THE PROJECT HAS PROGRESSED TO A
POINT THAT A CONTAINER IS NO LONGER REQUIRED.
10.0 CONTRACTOR IS RESPONSIBLE FOR PROTECTING ALL AREAS USED TO BRING
SUPPLIES AND EQUIPMENT INTO THE PROJECT AREA. ANY DAMAGE TO AREAS
OUTSIDE THE PROJECT AREA INCLUDING BUT NOT LIMITED TO THE LOBBY AND
CORRIDOR SHALL BE REPAIRED AT NO COST TO THE OWNER.
1 10/11/18 ISSUE FOR DD REVIEW
2 11/12/18 ISSUE FOR 95% REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
SUBMITTAL REGISTRY
TITLE CATEGORY
CASEWORK PRODUCT DATA, SHOP DRAWINGS
FLOORING PRODUCT DATA
GYPSUM BOARD ASSEMBLIES PRODUCT DATA
GYPSUM PLASTER PRODUCT DATA
INTERIOR PAINT PRODUCT DATA
MILLWORK PRODUCT DATA, SHOP DRAWINGS
QUARTZ COUNTERTOPS PRODUCT DATA, SHOP DRAWINGS, SAMPLES
SEALANTS PRODUCT DATA
SELF LEVELING UNDERLAYMENT PRODUCT DATA
REF.UP
REF.
UP
1
23
4
5
6
7 4
4
5
SINK TO BE ABATED
PRIOR TO THE START
OF CONSTRUCTION
UNDER SEPARATE
CONTRACT. GC TO
COORDINATE DEMO
OF SINK WITH
ABATEMENT
CONTRACTOR.
4
EXISTING MARBLE TO
REMAIN AT WINDOW,
SEE DEMO PHOTO
6/A-101.
EXISTING MARBLE TO
REMAIN AT WINDOW
8
9
B09
B08
B00UB
B00CA
B06
B00SB
B00CB
A-101
5
43
2 1/2" 18 GA. G90 METAL STUDS AT 16"
O.C. WITH DEFLECTION HEAD TRACK
AND 5/8" MOISTURE RESISTANT
GYPSUM WALL BOARD. ATTACH TO
WALLS, FLOOR, AND CEILING ABOVE
WITH 1/4" x 1 1/2 WEDGE BOLTS AT 16"
O.C. PROVIDE WOOD BLOCKING IN
WALL WHERE BASE/ WALL CABINETS
ARE TO BE LOCATED. TAPE, SPACKLE,
PRIME AND PAINT (PT-1).
1
EXISTING MARBLE COUNTER TOP
TO REMAIN AT WINDOW OPENING.2 3
PROVIDE NEW
COUNTERTOP TO
MATCH KITCHEN
2
B00CB
B09
B00CA
B00UB
B06
B00SB
B08
LVT CPT
10' - 0" +/-16' - 8" +/-14' - 9" +/-14' - 10" +/-V.I.F.
14' - 4" +/-FIN. WALL TO FACE OF STUD6' - 4 1/2"PATCH EXISTING WALLS WITH
PLASTER WHERE MARBLE WAS
REMOVED (TYP). PRIME AND PAINT
(PT-1).
PROVIDE TRANSITION STRIP
AT DOOR/ EXISTING CARPET
TO REMAIN.
REMOVE EXISTING
MARBLE PANELS
(TYP). PATCH
EXISTING WALLS
WITH PLASTER
WHERE MARBLE
WAS REMOVED
(TYP). PRIME AND
PAINT (PT-1).
EXISTING MARBLE
TO REMAIN
PROVIDE
INSULATED METAL
PANEL SCREWED
TO EXISTING
WINDOW WHERE
DUCTWORK WAS
REMOVED. SEAL
AROUND OPENING
WITH SEALANT.
CUSTOM 18" DEEP
BASE CABINETS THIS
WALL ONLY. ALL
OTHER CABINETS
ARE FULL 24" DEPTH.
PROVIDE WALL
CABINETS WITHOUT
DOORS (TYP)
QUARTZ COUNTERTOP
AND 4" BACKSPLASHNEW APPLIANCES
(PROVIDED BY
OWNER AND
INSTALLED BY GC)
PROVIDE WOOD
BASE TRIM TO MATCH
CABINETS AT TOE
KICK .
PT-1
PT-1
PT-1 PROVIDE CUSTOM
FILLER PANEL AT
CORNER.
1 1/4"
WC-1
36"
WC-4
36"
WC-3
18"7/8"
WC-5
30"7/8"
WC-3
18"
WC-2
30"1"84"30"18"36"12"7/8"SB-1
30"
BC-1
18"
7/8"
30"
7/8"BC-1
18"36"
BC-2
18"
1 1/4"
18" D
EXISTING MARBLE
TO REMAIN AT
WINDOW. PROVIDE
WOOD TRIM, PAINT.
PT-1
PT-4
PT-3
EXISTING CAST-IN-
PLACE BASE, PAINT
PT-130"18"36"84"24" D
2 5/8"BC-3
18"
BC-4
30"1 1/4"CORNE
LL U N I V
E
RSI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER TOWER/ NORTH/ SOUTH
BAKER COMPLEX
KITCHEN
RENOVATIONS
A-101
11121224
BAKER TOWER
KITCHEN
DEMOLITION
AND
RENOVATION
PLANS
J. COOLBAUGH
JGC
3004
DECEMBER 17, 2018
#
A-101 DEMOLITION KEY NOTES
1 REMOVE EXISTING VINYL FLOORING AND MASTIC.
2 REMOVE EXISTING ACT CEILING AND GRID.
3 REMOVE EXISTING CABINETS, COUNTERTOPS AND ALL BLOCKING.
4 REMOVE AND SALVAGE EXISTING MARBLE PANEL AND TRIM TO THE EXTENTS
SHOWN ON DRAWING. TURN OVER TO OWNER
5 REMOVE EXISTING APPLIANCES. COORDINATE WITH OWNER.
6 REMOVE EXISTING DOOR.
7 REMOVE EXISTING ROLLING COUNTER DOOR.
8 REMOVE EXISTING COUNTERTOP.
9 REMOVE EXISTING CARPET IN IT'S ENTIRETY.
#
0' 2' 4' 8'
SCALE: 1/4"=1'-0"
SCALE:1/4" = 1'-0"1 DEMOLITION PLAN - TOWER BASEMENT
SCALE:1/4" = 1'-0"2 RENOVATION PLAN - TOWER BASEMENT
SCALE: NO SCALE
6 DEMO PHOTO
SCALE: NO SCALE
5 INTERIOR ELEVATION
SCALE: NO SCALE
3 INTERIOR ELEVATION
SCALE: NO SCALE
4 INTERIOR ELEVATION
A-101 RENOVATION KEY NOTES
1 SCRAPE LOOSE PAINT FROM UNDERSIDE OF FLOOR/ CEILING ABOVE. PREP AREA
FOR PAINT. PRIME AND PAINT UNDERSIDE OF FLOOR ABOVE, CONDUIT, AND PIPING.
PAINT PT-2.
2 PROVIDE NEW LVT FLOORING.
3 PROVIDE NEW CARPET TILE.
GENERAL NOTES:
1. FIELD VERIFY ALL DIMENSIONS PRIOR TO CABINET/APPLIANCE
INSTALLATION NOTE MINIMUM CLEARANCE REQUIREMENTS.
2. PROVIDE FILLERS AS REQUIRED TO ALLOW PROPER CLEARANCE FOR
DRAWERS, DOORS, & HARDWARE.
3. PATCH WALLS WITH LIKE MATERIALS AFTER THE REMOVAL OF
EQUIPMENT, DOORS, WALLS, WINDOWS, ETC. PRIME AND PAINT.
KITCHEN CABINETS AND COUNTERTOP:
1. CABINETS -DURA SUPREME -CRESTWOOD HUDSON DOOR IN OAK
• ALL PLYWOOD CONSTRUCTION, SOLID HARDWOOD
DOVETAILED DRAWERS
• SOFT CLOSE HINGES AND FULL EXTENSION, SOFT CLOSE
DRAWER TRACKS BY BLUM
• PROVIDE UPPER CABINETS WITHOUT DOORS
• HARDWARE -LIBERTY 3/4" X 3" STEEL BAR PULL, BRUSHED
STAINLESS STEEL FINISH
• 5-10 YEAR WARRANTY
• FULLY SEALED FINISH
2. COUNTERTOPS -CORIAN QUARTZ BY DUPONT,
• 1 1/8 THICK WITH FULL BULLNOSE EDGE
• 4" BACKSPLASH & SIDESPLASH
• COLOR: AS SELECTED FROM FULL LINE COLOR CHART
PAINT:
PT-1 -WALL PAINT -BENJAMIN MOORE, ECOSPEC -COLOR (TBD BY OWNER)
PT-2 -CEILING PAINT -BENJAMIN MOORE, ECOSPEC -COLOR (TBD BY OWNER)
PT-3 - DOOR FRAMES -BENJAMIN MOORE, ECOSPEC -COLOR (TBD BY OWNER)
PT-4 -EXISTING WALL BASE -BENJAMIN MOORE, ECOSPEC -COLOR (TBD BY OWNER)
CASEWORK SCHEDULE
MARK WIDTH HEIGHT DEPTH MANUFACTURER
(N) GROUND FLOOR
BC-5 1' - 6" 2' - 8 3/4" 2' - 0" DURASUPREME
BC-6 1' - 3" 2' - 8 3/4" 2' - 0" DURASUPREME
SB-2 2' - 6" 2' - 8 3/4" 2' - 0" DURASUPREME
WC-2 2' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-3 1' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-4 3' - 0" 1' - 0" 2' - 0" DURASUPREME
WC-5 2' - 6" 1' - 0" 1' - 0" DURASUPREME
(S) GROUND FLOOR
BC-5 1' - 6" 2' - 8 3/4" 2' - 0" DURASUPREME
BC-6 1' - 3" 2' - 8 3/4" 2' - 0" DURASUPREME
SB-2 2' - 6" 2' - 8 3/4" 2' - 0" DURASUPREME
WC-2 2' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-3 1' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-4 3' - 0" 1' - 0" 2' - 0" DURASUPREME
WC-5 2' - 6" 1' - 0" 1' - 0" DURASUPREME
(T) BASEMENT
BC-1 1' - 6" 2' - 10 7/8" 2' - 0" DURASUPREME
BC-2 1' - 6" 2' - 10 7/8" 2' - 0" DURASUPREME
BC-3 1' - 6" 2' - 10 7/8" 1' - 6" DURASUPREME
BC-4 2' - 6" 2' - 10 7/8" 1' - 6" DURASUPREME
SB-1 2' - 6" 2' - 10 7/8" 2' - 0" DURASUPREME
WC-1 3' - 0" 2' - 6" 1' - 0" DURASUPREME
WC-2 2' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-3 1' - 6" 2' - 6" 1' - 0" DURASUPREME
WC-4 3' - 0" 1' - 0" 2' - 0" DURASUPREME
WC-5 2' - 6" 1' - 0" 1' - 0" DURASUPREME
FLOORING:
1. PROVIDE ARDEX LU 100 SELF LEVELING UNDERLAYMENT
MANNINGTON PLANK:
• NATURES PATHS -#12237 MADISON MAPLE PEPPER BARK 6" X 36"
PLANK
INTERFACE CARPET TILE:
• MONOCHROME CARPET TILE (MAIN COLOR -TBD BY OWNER)
• MONOCHROME CARPET TILE (BOARDER COLOR -TBD BY OWNER)
1 10/11/18 ISSUE FOR DD REVIEW
2 11/12/18 ISSUE FOR 95% REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
REF.A-102 3
2
1
LVTEX. CPT
RELOCATED VENDING
MACHINE, COORDINATE
WITH CIT FOR
CONNECTIONS
FIN. EX. WALL TO F.O. STUDS
6' - 7" +/-25' - 0" +/-(N) G10
(N) G08
(N) G09
PROVIDE 5/8" MOISTURE
RESISTANT GYPSUM
WALL BOARD ATTACHED
TO EXISTING STUD WALL.
PROVIDE WOOD
BLOCKING IN WALL
WHERE BASE/ WALL
CABINETS ARE TO BE
LOCATED. TAPE,
SPACKLE, PRIME AND
PAINT (PT-1).
PROVIDE TRANSITION STRIP
EXISTING MARBLE TO
REMAIN AT WINDOW.
(N) G08
(N) G10
(N) G09
1
EXISTING CASEWORK AND
FLOORING TO BE DEMOED
(IN THIS AREA) AS PART OF
BATHROOM RENOVATION
PROJECT (UNDER A
DIFFERENT CONTRACT)
PRIOR TO THE START OF
THIS PROJECT.
PROVIDE TEMPORARY
CONSTRUCTION
PARTITION WITH DOOR
PRIOR TO START OF
KITCHEN RENOVATION 25' - 0" +/-BC-6
15"
CLEAR
36"
BC-6
15"
V.I.F.
33" +/-
BC-5
18"
SB-2
30"
BC-5
18"
1 1/2" +/-
WC-5
30"
1 1/2" +/-
WC-3
18"
WC-2
30"
WC-3
18"
3/4"
WC-4
36"3/4"
PROVIDE CUSTOM
END CLOSURE
PANEL.
QUARTZ COUNTERTOP WITH
FULL BULLNOSE AND 4"
BACKSPLASH. PROVIDE
BRACKETS AT OPEN AREA.
NEW APPLIANCES
(PROVIDED BY OWNER
AND INSTALLED BY GC)
PROVIDE WOOD BASE TRIM TO
MATCH CABINETS AT TOE
KICK .
PT-1
PROVIDE CUSTOM TOE
KICK/ FILLER PANEL AT
STOVE.30"20"84"RELOCATED VENDING MACHINE,
COORDINATE WITH CIT FOR
CONNECTIONS
MIN.27"WALL BASE
(BEYOND)
WALL BASE TO MATCH
EXISTING
PROVIDE CUSTOM WOOD
VALANCE. COLOR AND WOOD
TYPE TO MATCH CABINETS.
ATTACHED TO EACH SIDE WITH
ANGLE BRACKETS.
PROVIDE ADA SINK
BASE CABINET CORNE
LL U N I V
E
RSI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER TOWER/ NORTH/ SOUTH
BAKER COMPLEX
KITCHEN
RENOVATIONS
A-102
11121224
BAKER NORTH
KITCHEN
DEMOLITION
AND
RENOVATION
PLANS
J. COOLBAUGH
JGC
3004
DECEMBER 17, 2018
SCALE: 1/4" = 1'-0"
2 RENOVATION PLAN - NORTH GROUND FLOOR
SCALE: 1/4" = 1'-0"
1 DEMOLITION PLAN - NORTH GROUND FLOOR
A-102 DEMOLITION KEY NOTES
1 REMOVE EXISTING GYPSUM WALL BOARD. EXISTING STUDS TO REMAIN. REVIEW
CONDITION OF EXISTING STUDS, IF RUSTED OR ROTTED, PROVIDE NEW G90 STUDS
TO MATCH EXISTING.
SCALE: 1/4" = 1'-0"
3 INTERIOR ELEVATION
A-102 RENOVATION KEY NOTES
1 SCRAPE LOOSE PAINT FROM UNDERSIDE OF FLOOR/ CEILING ABOVE. PREP AREA
FOR PAINT. PRIME AND PAINT UNDERSIDE OF FLOOR ABOVE, CONDUIT, AND PIPING.
PAINT PT-2.
2 PROVIDE NEW PLANK FLOORING. REFER TO A-101 FOR SPEC.
0' 2' 4' 8'
SCALE: 1/4"=1'-0"
#
#
1 10/11/18 ISSUE FOR DD REVIEW
2 11/12/18 ISSUE FOR 95% REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
GENERAL NOTES:
1. FIELD VERIFY ALL DIMENSIONS PRIOR TO CABINET/APPLIANCE INSTALLATION
NOTE MINIMUM CLEARANCE REQUIREMENTS.
2. PROVIDE FILLERS AS REQUIRED TO ALLOW PROPER CLEARANCE FOR DRAWERS,
DOORS, & HARDWARE.
3. PATCH WALLS WITH LIKE MATERIALS AFTER THE REMOVAL OF EQUIPMENT,
DOORS, WALLS, WINDOWS, ETC. PRIME AND PAINT.
4. REFER TO A-101 FOR SPECIFICATION INFORMATION.
REF.EXISTING MARBLE TO
REMAIN AT WINDOW.
1
(S) G08
(S) G10
(S) G09
EXISTING CASEWORK AND
FLOORING TO BE DEMOED
(IN THIS AREA) AS PART OF
BATHROOM RENOVATION
PROJECT (UNDER A
DIFFERENT CONTRACT)
PRIOR TO THE START OF
THIS PROJECT.
PROVIDE TEMPORARY
CONSTRUCTION
PARTITION WITH DOOR
PRIOR TO START OF
KITCHEN RENOVATION 25' - 6" +/-A-102 3 SIM
PROVIDE 5/8" MOISTURE
RESISTANT GYPSUM
WALL BOARD ATTACHED
TO EXISTING STUD WALL.
PROVIDE WOOD
BLOCKING IN WALL
WHERE BASE/ WALL
CABINETS ARE TO BE
LOCATED. TAPE,
SPACKLE, PRIME AND
PAINT (PT-1).
2
1
FIN. EX. WALL TO F.O. STUDS
6' - 5" +/-25' - 6" +/-LVTEX. CPT
RELOCATED VENDING
MACHINE, COORDINATE
WITH CIT FOR
CONNECTIONS
(S) G10
(S) G08
(S) G09
PROVIDE TRANSITION STRIP CORNE
LL U N I V
E
RSI
TYFOUN
D E D 5681AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.FCS.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER TOWER/ NORTH/ SOUTH
BAKER COMPLEX
KITCHEN
RENOVATIONS
A-103
11121224
BAKER SOUTH
KITCHEN
DEMOLITION
AND
RENOVATION
PLANS
J. COOLBAUGH
JGC
3004
DECEMBER 17, 2018
SCALE:1/4" = 1'-0"1 DEMOLITION PLAN - SOUTH GROUND FLOOR
SCALE: 1/4" = 1'-0"
2 RENOVATION PLAN - SOUTH GROUND FLOOR
A-103 DEMOLITION KEY NOTES
1 REMOVE EXISTING GYPSUM WALL BOARD. EXISTING STUDS TO REMAIN. REVIEW
CONDITION OF EXISTING STUDS, IF RUSTED OR ROTTED, PROVIDE NEW G90 STUDS
TO MATCH EXISTING.
A-103 RENOVATION KEY NOTES
1 SCRAPE LOOSE PAINT FROM UNDERSIDE OF FLOOR/ CEILING ABOVE. PREP AREA
FOR PAINT. PRIME AND PAINT UNDERSIDE OF FLOOR ABOVE, CONDUIT, AND PIPING.
PAINT PT-2.
2 PROVIDE NEW PLANK FLOORING. REFER TO A-101 FOR SPEC.
0' 2' 4' 8'
SCALE: 1/4"=1'-0"
#
#
1 10/11/18 ISSUE FOR DD REVIEW
2 11/12/18 ISSUE FOR 95% REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
GENERAL NOTES:
1. FIELD VERIFY ALL DIMENSIONS PRIOR TO CABINET/APPLIANCE INSTALLATION
NOTE MINIMUM CLEARANCE REQUIREMENTS.
2. PROVIDE FILLERS AS REQUIRED TO ALLOW PROPER CLEARANCE FOR DRAWERS,
DOORS, & HARDWARE.
3. PATCH WALLS WITH LIKE MATERIALS AFTER THE REMOVAL OF EQUIPMENT,
DOORS, WALLS, WINDOWS, ETC. PRIME AND PAINT.
4. REFER TO A-101 FOR SPECIFICATION INFORMATION.
(T) BASEMENT
686' -0"
(N) GROUND FLOOR
677' -0"
(S) GROUND FLOOR
685' -0"
3/4" HHWS
TO WITHIN WALL
3/4" HHWR
TO WITHIN WALL
CONNECT TO EXISTING
HHWS AND HHWR
3/4" HHWS AND HHWR
TO WITHIN WALL CAVITY
BALANCING
VALVE BV-1
FCU-G09
CONTROL
VALVE CV-G09
SUPPLY RETURN
BALL
VALVE V-1 (TYP. OF 2)
BALANCING
VALVE
PRESSURE/TEMPERATURE
TEST PORT (TYP. OF 2)
MANUAL
AIR VENT
COIL
STRAINER BLOWDOWN
WITH BRASS HOSE
CONNECTION, CAP WITH
CHAIN
COIL DRAIN
WITH BRASS
HOSE
CONNECTION,
CAP AND
CHAIN (TYP.)CORNE
LL
U N I V
E
RSI
TYFOUN
D E D 5681
AD
FACILITIES
ENGINEERING
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.IPP.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER COMPLEX
BAKER COMPLEX
KITCHEN
RENOVATIONS
MP-001
11121224
GENERAL
NOTES,
SCHEDULES,
AND SYMBOL
LEGENDS
T. FISHER
TRF
3004
December 17, 2018
MECHANICAL ABBREVIATIONS
CO CLEAN OUT
CD CONDENSATE DRAIN
DHWS DOMESTIC COLD WATER SUPPLY
DHWR DOMESTIC HOT WATER RETURN
DCWR DOMESTIC HOT WATER SUPPLY
FTR FIN TUBE RADIATION
FP FIRE PROTECTION
HHWR HEATING HOT WATER RETURN
HHWS HEATING HOT WATER SUPPLY
PF PLUMBING FIXTURE
SAN SANITARY
V VENT
WCO WALL CLEANOUT
MECHANICAL SYMBOLOGY
2-WAY ELECTRIC CONTROL VALVE
3-WAY ELECTRIC CONTROL VALVE
ACOUSTICALLY ALIGNED DUCTWORK
AIRFLOW
AQUA STAT
AUTOMATIC LOUVERED DAMPER IN DUCT
BACKFLOW PREVENTER
BALANCE VALVE
BALL VALVE
BOTTOM PIPE CONNECTION
BUTTERFLY VALVE
CAP OR PLUG
CHECK VALVE
CIRCULATING PUMP
DIRECTION OF FLOW
DUCT AIRFLOW
DUCT DOWN (EXHAUST OR RETURN)
DUCT DOWN (SUPPLY)
DUCT UP (EXHAUST OR RETURN)
DUCT UP (SUPPLY)
EXHAUST FAN
EXHAUST OR RETURN UP THROUGH NEXT FLOOR OR ROOF
EXPANSION COMPENSATOR WITH EXPANSION GUIDES
EXPANSION JOINT
FIRE AND SMOKE DAMPER IN DUCT
FIRE DAMPER IN DUCT
FLANGE CONNECTION
FLEX CONNECTOR
FLEXIBLE CONNECTION
FLEXIBLE DUCT
FLOW METER
FLOW SWITCH
FUSIBLE LINK VALVE
GLOBE VALVE
MANUAL AIRVENT
ORIFICE METER
PIPE ANCHOR
PIPE DOWN
PIPE GUIDE
PIPE UP
PIPING REDUCER (CONCENTRIC)
PIPING REDUCER (ECCENTRIC)
PITCH PIPING (DOWN)
PRESSURE GAUGE
PRESSURE OR TEMPERATURE PETES PLUG
PRESSURE REDUCING VALVE
PRESSURE SWITCH
RECTANGULAR ELBOW
RECTANGULAR ELBOW WITH TURNING VANES
RELIEF VALVE
ROOF TOP HOOD
SMOKE DAMPER IN DUCT
SOLENOID VALVE
STANDARD BRANCH DUCT
STEAM TRAP
STRAINER (DUPLEX)
STRAINER WITH BLOWDOWN VALVE AND CAP
SUPPLY THROUGH NEXT FLOOR OR ROOF
TEMPERATURE WELL
THERMOMETER
THERMOMETER (DIAL)
TOP PIPE CONNECTION
TRIPLE DUTY VALVE
UNION CONNECTION
VACUUM BREAKER
VOLUME DAMPER IN DUCT
GENERAL DRAWING SYMBOLOGY
DEMOLISHED WORK
EXISTING PIPING TO REMAIN
EXISTING TO REMAIN
EXISTING WORK TO REMAIN
NEW WORK
POINT OF CONNECTION
POINT OF DISCONNECTION
PLUMBING FIXTURE SCHEDULE & SPEC
TAG DESCRIPTION
BOD
MANUFACTURER MODEL DIMENSIONS MATERIAL FINISH / COLOR COLD WATER HOT WATER
WASTE /
SANITARY VENT NOTES STANDARDS
PF-1 SINK - UNDERMOUNT ELKAY ECTSRAD25226BG 25" X 22" X 6" 304 STAINLESS STEEL POLISHED SATIN 1-1/2" 1-1/4" MINIMUM CABINET SIZE 36"ADA COMPLIANT
FAUCET - DECK MOUNT MOEN CA87003RS N/A METAL STAINLESS 1/2" 1/2"SINGLE HANDLE, 3/8" COMPRESSION FITTING CONNECTIONS ADA COMPLIANT
SUPPLIES - ANGLE (LOOSE KEY) T&S BRASS B-1335 1/2" NPT INLET BRASS CHROME 1/2" 1/2"COORDINATE OUTLET CONNECTION WITH FAUCET
DRAIN ASSEMBLY DAYTON D1125 3-1/2" DIAMETER STAINLESS STEEL MATTE 1-1/2" GRID DRAIN WITH REMOVABLE STRAINER
MECHANICAL/PLUMBING/FIRE PROTECTION PIPE AND FITTING SCHEDULE AND SPECIFICATIONS
PIPE SERVICE ABBREVIATION PIPE SIZE MATERIAL FITTINGS JOINT INSULATION
DOMESTIC WATER DCWS / DHWS 1-1/2" & BELOW ASTM B88 TYPE L COPPER ASTM B16.22 STD WROUGHT COPPER ASTM B32 SOLDER 1/2" THICK FIBERGLASS, K=0.27 (MAX) WITH VAPOR RETARDER
SANITARY DRAIN AND VENT SAN / V 2" & BELOW ASTM B306 DWV COPPER ASME B16.29 TYPE DWV WROUGHT COPPER ASTM B32 SOLDER N/A
SANITARY DRAIN AND VENT SAN / V 2-1/2" & ABOVE ASTM A74, ASTM A888 SERVICE WEIGHT CAST IRON ASTM A74, ASTM A888 CAST IRON NO-HUB ASTM C1277 NEOPRENE GASKET SS BANDS N/A
HEATING HOT WATER HWS/HWR 1-1/4" & BELOW ASTM B88 TYPE L COPPER ASTM B16.22 STD WROUGHT COPPER ASTM B32 SOLDER 1-1/2" THICK FIBERGLASS, K=0.29 (MAX) WITH VAPOR RETARDER
DRY SPRINKLER DSP 2" & SMALLER ASTM A53, A135 OR A795 STEEL, SCH 40 BLACK ASME B16.3 MALLEABLE IRON, CLASS 125 AND 300 THREADED N/A
MECH/PLUMBING/FP SCOPE OF WORK
1.0 PROVIDE PLUMBING, MECHANICAL, AND FIRE PROTECTION SYSTEM MODIFICATIONS
AS REQUIRED TO SUPPORT THE RENOVATION OF THE NORTH, SOUTH, AND TOWER
KITCHENS AT THE BAKER COMPLEX.
2.0 TOWER - DEMOLITION OF EXISTING EXHAUST FAN, DUCTWORK, GRILLE, AND
ACCESSORIES.
3.0 TOWER/NORTH/SOUTH - SELECTIVE DEMOLITION OF EXISTING DOMESTIC WATER
AND SANITARY DRAIN/VENT PIPING.
4.0 TOWER/NORTH/SOUTH - PROVIDE KITCHEN SINK, FAUCET, AND ACCESSORIES.
5.0 TOWER/NORTH/SOUTH - PROVIDE DOMESTIC WATER AND SANITARY DRAIN PIPING
AS REQUIRED TO CONNECT SINK TO EXISTING SERVICES.
6.0 NORTH/SOUTH - DEMOLITION OF EXISTING FIN-TUBE, PIPING, VALVE, AND
ACCESSORIES.
7.0 NORTH/SOUTH - PROVIDE FIN TUBE, ENCLOSURE, TEMPERATURE CONTROL,
HEATING HOT WATER SUPPLY/RETURN PIPING, AND ACCESSORIES.
8.0 TOWER - DISCONNECT AND REMOVE SPECIFIED SPRINKLERS AND PIPING AS
REQUIRED TO PROVIDE PROPER SPRINKLER PROTECTION DUE TO CEILING
REMOVAL.
9.0 NORTH/SOUTH - TEST AND BALANCE HYDRONIC SYSTEM ASSOCIATED WITH NEW
FIN-TUBE RADIATION, SUBMIT REPORT.
MECHANICAL/PLUMBING GENERAL NOTES
1.0 DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL ARRANGEMENT
OF SYSTEMS AND WORK INCLUDED IN THE CONTRACT. CONTRACTOR SHALL
FIELD VERIFY ALL DIMENSIONS. IF DIMENSIONS OR CONDITIONS ARE FOUND
TO BE IN CONFLICT WITH THE DRAWINGS, THE CONTRACTOR SHALL
IMMEDIATELY REFER THE CONFLICT TO THE ENGINEER.
2.0 UTILITY SHUTDOWNS: SHUTDOWN OF ANY BUILDING UTILITY SYSTEM SHALL
BE COORDINATED WITH CUSTOMER SERVICE AT PH: 607-255-5322. THE
CONTRACTOR SHALL BEAR THE COST OF THE UTILITY SHUTDOWN.
SCHEDULE WORK TEN DAYS IN ADVANCE AND NOTIFY THE OWNER'S
REPRESENTATIVE TO COORDINATE BUILDING FUNCTIONS WITH THE
BUILDING COORDINATOR.
3.0 ALL PENETRATIONS THROUGH FULL HEIGHT WALLS ARE TO BE FIRESTOPPED
IN ACCORDANCE WITH UL STANDARDS. ALL GAPS AND JOINTS AT RATED
FLOORS, ROOFS AND WALLS ARE TO BE FIRE AND SMOKE STOPPED. CAPS
AND JOINTS INCLUDE (BUT ARE NOT LIMITED TO) TOP OF WALL TO FLOOR OR
ROOF DECK, WALL TO BEAMS, AND CONTROL OR EXPANSION JOINTS.
FIRESTOPPING INCLUDES BOTH FORM OR PACKING MATERIAL AND THE FILL,
VOID OR CAVITY MATERIAL.
4.0 INSTALL EQUIPMENT TO ENSURE PROPER ACCESS AND WITH SUFFICIENT SPACE TO
PERFORM ROUTINE MAINTENANCE AND
REPAIR. EQUIPMENT THAT IS NOT INSTALLED WITH THIS REQUIREMENT IN
MIND SHALL BE RELOCATED AT NO EXPENSE TO THE UNIVERSITY UNTIL
DEFICIENCIES ARE CORRECTED.
5.0 ALL SYSTEM TESTING SHALL BE CONDUCTED PRIOR TO INSULATION,
FIREPROOFING, AND ENCLOSURE IN SHAFTS. ANY RESTORATION WORK
REQUIRED AS A RESULT OF DISTURBING FINISHES OR STRUCTURE IN ORDER
TO ACCESS SYSTEMS REQUIRING REPAIR SHALL BE AT NO COST TO THE
UNIVERSITY.
6.0 VERIFY FINAL EQUIPMENT/FIXTURE LOCATIONS FOR ROUGHING-IN.
7.0 ANY FIRESTOPPING DISTURBED DURING THE COURSE OF WORK SHALL BE
REPAIRED TO MAINTAIN A 2-HOUR FIRE RATING.
8.0 CUTTING AND PATCHING: THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL
CUTTING, FITTING, AND PATCHING TO COMPLETE THE WORK. WHERE EXISTING
CONSTRUCTION IS REMOVED, CAUSING AN EXPOSURE OF UNFINISHED AND/OR
DAMAGED SURFACES, RESULTING SURFACES SHALL BE RECONSTRUCTED WITH
MATERIALS TO MATCH FINISHED AREAS.
FIRE PROTECTION GENERAL NOTES
1.0 IT IS THE INTENT OF THESE DRAWINGS TO PROVIDE MODIFICATIONS TO THE
EXISTING DRY-PIPE FIRE PROTECTION SYSTEM FOR THE PROTECTION OF THE
BAKER TOWER B08 SPACE RENOVATIONS.
2.0 PRIOR TO ALTERATIONS, THE SPRINKLER CONTRACTOR SHALL FIELD VERIFY
EXTENT OF ALTERATION AND NEW WORK, WITH REGARD TO EXISTING CONDITIONS
AT PIPE PENETRATIONS THROUGH FLOORS, WALLS, CEILINGS AND SOFFITS.
3.0 ALL SPRINKLER COMPONENTS SHALL BE UNDERWRITER'S LABORATORIES (UL) AND
FACTORY MUTUAL (FM) APPROVED.
4.0 THE DRAWINGS ARE DIAGRAMMATIC AND INDICATE ONLY THE GENERAL
ARRANGEMENT OF THE ITEMS INCLUDED IN THE FIRE PROTECTION WORK. AS
SUCH, CONTRACTOR SHALL PROVIDE A COMPLETE SPRINKLER SYSTEM IN STRICT
ACCORDANCE WITH THE REQUIREMENTS OF FM GLOBAL STANDARDS, THE NFPA
13-INSTALLATION OF FIRE PROTECTION SYSTEMS, THE NEW YORK STATE BUILDING
CODES, THE NEW YORK STATE FIRE CODES, LOCAL CODES, AND GOVERNING
AUTHORITIES. THE DESIGN OF FIRE PROTECTION SYSTEMS TO WITHSTAND SEISMIC
EVENTS SHALL BE IN ACCORDANCE WITH THE CRITERIA DEVELOPED BY THE NFPA.
5.0 SPRINKLER COVERAGE OR HEAT DETECTION SHALL BE MAINTAINED AT ALL TIMES
DURING THE RENOVATION. CONTRACTOR SHALL REQUEST SPRINKLER SYSTEM
SHUTDOWNS WITH THE BUILDING COORDINATOR A MINIMUM OF TEN (10) DAYS
PRIOR TO THE SHUTDOWN DATE. THE CONTRACTOR SHALL BEAR THE COST OF
THE UTILITY SHUTDOWN. NOTIFY THE OWNER'S REPRESENTATIVE TO COORDINATE
BUILDING FUNCTIONS WITH THE BUILDING COORDINATOR.
6.0 COORDINATE THE EXACT LOCATION OF SPRINKLERS, EQUIPMENT, AND DEVICES
WITH ARCHITECTURAL, MECHANICAL, ELECTRICAL AND ALL OTHER TRADES
DRAWINGS PRIOR TO ROUGH-IN AND INSTALLATION.
7.0 SPRINKLER PIPING SHALL BE ARRANGED TO DRAIN THROUGH THE MAIN DRAIN
VALVE WHENEVER PRACTICAL. ALL TRAPPED SECTIONS OF PIPE, EXCEPT THOSE
SUPPLYING A SINGLE SPRINKLER, SHALL BE PROVIDED WITH A DRUM-DRIP
ASSEMBLY.
8.0 PENETRATIONS THROUGH CONCRETE FLOORS AND WALLS SHALL BE MADE WITH
GALVANIZED PIPE SLEEVES. ALL PENETRATIONS SHALL CONTAIN FIRE STOPPING
WITH A FIRE RATING EQUAL TO THAT OF THE AREA BEING PENETRATED.
9.0 SPRINKLER PIPING SHALL BE LABELED.
10.0 AFTER ALL WORK HAS BEEN COMPLETED, ACCEPTANCE TESTING SHALL BE
SCHEDULED THROUGH EH&S, AND SHALL BE WITNESSED BY EH&S AND CITY OF
ITHACA REPRESENTATIVES.
11.0 AIR TEST SHALL BE AT SYSTEM OPERATING PRESSURE, FOR A PERIOD OF
24-HOURS.
12.0 ANY FIRESTOPPING DISTURBED DURING THE COURSE OF WORK SHALL BE
REPAIRED TO MAINTAIN A 2-HOUR FIRE RATING.
SPRINKLER SCHEDULE
SPRINKLER TYPE SERVES MANF BOD MODEL BOD (SIN) RESPONSE ORIFICE (IN) K-FACTOR
TEMPERATURE RATING
(DEG F)CONSTRUCTION FINISH
UPRIGHT KITCHEN B08 RELIABLE F1FR-56 (RA1425) QUICK 1/2 5.6 155 BRASS BRONZE
1 SOLDER FILLER METALS: ASTM B32, LEAD-FREE ALLOYS. INCLUDE WATER FLUSHABLE FLUX ACCORDING TO ASTM B813.
2 PIPE NIPPLES: SAME QUALITY, MATERIAL, CLASS AS PIPING. CLOSE NIPPLES ARE NOT PERMITTED.
3 INSTALL PLUMBING SYSTEMS TO FACILITATE SERVICE, MAINTENANCE AND REPAIR OR REPLACEMENT OF COMPONENTS.
4 USE APPROVED FITTINGS TO MAKE CHANGES IN DIRECTION, BRANCH TAKEOFFS FROM MAINS, AND REDUCTIONS IN PIPE SIZE.
5 PROVIDE DRAINS FOR COMPLETE SPRINKLER SYSTEM DRAINAGE, PER NFPA.
6 ALL WASTE PIPING SHALL BE PITCHED AT 1/8" PER FOOT. ALL SUPPLY PIPING SHALL BE PITCHED BACK TOWARDS CONNECTION TO THE ROOM ENTRANCE.
7 PROVIDE VAPOR RETARDER ON PIPING INSULATION SYSTEMS CARRYING FLUIDS WITH AN OPERATING TEMPERATURE LOWER THAN 60 DEGREES F.
8 DO NOT ENCLOSE, COVER OR PUT PLUMBING PIPING SYSTEMS INTO OPERATION UNTIL IT HAS BEEN INSPECTED AND APPROVED BY THE AUTHORITIES HAVING JURISDICTION.
9 LEAVE NEW, ALTERED, EXTENDED, OR REPLACED DOMESTIC WATER PIPING UNCOVERED AND UNCONCEALED UNTIL IT HAS BEEN TESTED. EXPOSE WORK THAT WAS COVERED OR CONCEALED BEFORE IT WAS TESTED.
10 PROVIDE PIPE LABLES AND DIRECTIONAL ARROWS ON ALL NEW PIPING SYSTEMS. LABELS SHALL BE PRINTED PLASTIC WITH CONTACT-TYPE, PERMANENT ADHESIVE BACKING. LETTERS SHALL BE 1/4-INCH.
11 PAINT ALL UNINSULATED PIPING, WHEN EXPOSED TO VIEW.
12 ALL INSULATION AND ADHESIVE SHALL HAVE A MAXIMUM FLAME-SPREAD INDEX OF 25 AND A MAXIMUM SMOKE-DEVELOPED INDEX OF 50 WHEN TESTED IN ACCORDANCE WITH ASTM E84.
13 TESTING OF DOMESTIC WATER PIPING:
CAP AND SUBJECT DOMESTIC WATER PIPING TO STATIC WATER PRESSURE OF 50 PSIG ABOVE OPERATING PRESSURE, WITHOUT EXCEEDING PRESSURE RATING OF PIPING SYSTEM MATERIALS
ISOLATE TEST SOURCE AND ALLOW TO STAND FOR FOUR HOURS. LEAKS AND LOSS IN TEST PRESSURE CONSTITUTE DEFECTS THAT MUST BE REPAIRED
REPAIR LEAKS AND DEFECTS WITH NEW MATERIALS AND RETEST PIPING UNTIL SATISFACTORY RESULTS ARE OBTAINED.
14 TESTING OF DOMESTIC WASTE AND VENT PIPING:
CAP AND SUBJECT DOMESTIC WASTE AND VENT PIPING TO STATIC WATER PRESSURE OF 10 FEET HEAD PRESSURE ABOVE HIGHEST POINT OF SYSTEM UNDERGOING TEST
ISOLATE TEST SOURCE AND ALLOW TO STAND UNTIL SYSTEM CAN BE VISUALLY INSPECTED BY AUTHORITY HAVING JURISDICTION. LEAKS CONSTITUTE DEFECTS THAT MUST BE REPAIRED
REPAIR LEAKS AND DEFECTS WITH NEW MATERIALS AND RETEST PIPING UNTIL SATISFACTORY RESULTS ARE OBTAINED.
15 TESTING OF HYDRONIC SYSTEMS:
FILL SYSTEM WITH AMBIENT TEMPERATURE WATER. USE VENTS INSTALLED AT HIGH POINTS OF SYSTEM TO RELEASE AIR. USE DRAINS INSTALLED AT LOW POINTS FOR COMPLETE DRAINING OF TEST LIQUID.
ISOLATE EXPANSION TANKS AND DETERMINE THAT HYDRONIC SYSTEM IS FULL OF WATER
SUBJECT PIPING SYSTEM TO HYDROSTATIC TEST PRESSURE THAT IS NOT LESS THAN 1.5 TIMES THE SYSTEM WORKING PRESSURE. TEST PRESSURE SHALL NOT EXCEED MAXIMUM
AFTER HYDROSTATIC TEST PRESSURE HAS BEEN APPLIED FOR AT LEAST 10 MINUTES, EXAMINE PIPING, JOINTS, AND CONNECTIONS FOR LEAKAGE.
ELIMINATE LEAKS BY TIGHTENING, REPAIRING, OR REPLACING COMPONENTS, AND REPEAT HYDROSTATIC TEST UNTIL THERE ARE NO LEAKS.
ARRANGE FOR INSPECTION BY FACILITIES MANAGEMENT PIPE SHOP.
SCALE:1/2" = 1'-0"1 FINTUBE RADIATION ELEVATION
1 10/10/18 ISSUE FOR 50% DD REVIEW
2 11/12/18 ISSUE FOR 95% CD REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
CONTROL VALVE SCHEDULE & SPEC
TAG MANF VALVE MODEL
OPERATOR
MODEL SIZE (IN) CV CAPACITY (GPM) MAX PD (PSIG) TYPE
CV-G09S BELIMO CCV - B210 SGF24 1/2 1.9 0 - 2.6 4 2-WAY, PROPORTIONAL, SPRING RETURN
CV-G09N BELIMO CCV - B210 SGF24 1/2 1.9 0 - 2.6 4 2-WAY, PROPORTIONAL, SPRING RETURN
1 ACCEPTABLE MANUFACTURERS: BELIMO, VSI
2 ELECTRIC INPUT: 0-10VDC
3 TWO-WAY VALVES: EQUAL PERCENTAGE FLOW CHARACTERISTIC
4 CONSTRUCTION: CHARACTERIZING DISK, FORGED BRASS, NICKEL PLATED BODY, STAINLESS STEEL BALL AND STEM, FIBERGLASS REINFORCED PTFE SEAT
5 RATINGS: 400 PSI PRESSURE, 0-212 F MEDIA TEMPERATURE RANGE
6 ALL CONTROL WIRING SHALL BE INSTALLED IN CONDUIT.
CONTROL WIRING SHALL BE UNSPLICED FROM THE CONTROLLER TO THE SENSOR OR DEVICE.
TEST EACH POINT THROUGH IT FULL OPERATING RANGE TO VERIFY THAT SAFETY AND OPERATING CONTROL SET POINTS ARE AS REQUIRED.
7 PROVIDE WITH ENCLOSURE MOUNTED POSITIONER (OPERATOR)
PIPING ACCESSORIES SCHEDULE AND SPECIFICATIONS
TAG DEVICE
BOD
MANUFACTURER MODEL PRESSURE RATING SPECIFICATIONS
BV-1 BALANCE VALVE 3/4 INCH BELL & GOSSETT CB SERIES, CB 3/4 200 PSIG @ 250 DEGF 0.6 - 3.0 GPM RANGE, BRONZE, BALL OR PLUG TYPE BODY WITH CALIBRATED ORIFICE OR VENTURI; GLASS AND CARBON FILLED TFE OR EPDM SEAT
RINGS, EPDM STEM O-RING, WITH INTEGRAL SEALS FOR PORTABLE DIFFERENTIAL PRESSURE METER, WITH LEVEL HANDLE AND MEMORY STOP TO
RETAIN SET POSITION.
V-1 SHUT-OFF BALL VALVE WATTS B6000-SS 300 PSIG WOG MSS SP-110, 2-PIECE, STANDARD PORT, BRONZE BODY, 316 SS BALL & STEM, PTFE OR TFE SEAT
S-1 STRAINERS, WYE PATTERN WATTS SERIES 777 200 PSIG @ 210 ˚F WOG BRONZE BODY, #20 MESH 304 STAINLESS STEEL SCREEN, THREAD OR SWEAT CONNECTION.
AV-1 AIR VENTS BELL & GOSSETT MODEL 87 150 PSIG BRASS BODY, NON-FERROUS INTERNALS
1 FOR VALVES INSTALLED IN INSULATED PIPING SYSTEMS, PROVIDE EXTENDED HANDLE
2 PROVIDE VALVES WITH UNIONS OR FLANGES AT EACH PIECE OF EQUIPMENT ARRANGED TO ALLOW SERVICE, MAINTENANCE AND EQUIPMENT REMOVAL WITHOUT SYSTEM SHUTDOWN
3 PROVIDE STRAINERS AT INLET OF CONTROL VALVES, STEAM TRAPS, AIR SEPARATORS, AND WHERE INDICATED. INSTALL NIPPLE AND BALL VALVE IN BLOWDOWN CONNECTION.
4 PROVIDE MANUAL AIR VENTS AT HIGH POINTS IN PIPING SYSTEM, HEAT TRANSFER COILS, AND ELSEWHERE AS REQUIRED FOR SYSTEM AIR VENTING.
5 PROVIDE DRAIN VALVES AT MAIN SHUT-OFF VALVES, LOW POINTS OF PIPING SYSTEM, AND ELSEWHERE AS REQUIRED FOR SYSTEM DRAINING.
6 PROVIDE TAGS FOR ALL NEW CONTROL AND SHUT-OFF VALVES. TAGS SHALL BE BRASS, 1-1/2-INCH ROUND, WITH STAMPED LETTERS AND NUMBERS. PROVIDE VALVE CHART.
SCALE:1" = 1'-0"2 FAN COIL UNIT COIL PIPING DETAIL
FAN COIL UNIT SCHEDULE
TAG SERVES MAF BOD MODEL BOD CFM
HEATING COIL ELECTRICAL
CAPACITY
(MBH)
AIR SIDE WATER SIDE
FLA V / PH / HZEAT DB (F) ESP (IN WG) EWT (F) LWT (F) GPM WPD (FT) TYPE
FCU-G09 KITCHENETTE G09 TRANE FFJB0401B 400 27.12 70 NONE 140 110 1.81 4.61 3-ROW 3.10 115 / 1 / 60
1 RATINGS: ARI 440, ASHRAE 33, UL 1995
2 COIL: COPPER TUBE, ALUMINUM FINS, TESTED TO 200 PSIG, 220 DEGREE ENTERING WATER TEMPERATURE, WITH MANUAL AIR VENT AND DRAIN VALVE, LEFT HAND CONNECTIONS WITHOUT AUXILIARY DRAIN
3 FAN: DOUBLE WIDTH, DOUBLE INLET, FORWARD CURVED, CENTRIFUGAL
4 MOTOR: ECM
5 CABINET: VERTICAL SLOPE TOP, FRONT TOE SPACE INLET, TOP BAR GRILLE OUTLET, BAKED ENAMEL FINISH, COLOR SELECTED BY OWNER FROM STANDARD COLOR CHART , WITH 1/2-INCH COATED FIBERGLASS
INSULATION, LEVELING FEET
6 FILTERS: MERV 8
7 OPTIONAL ACCESSORIES: UNIT MOUNTED ZONE SENSOR MODULE, FACTORY INSTALLED
8 INSTALL FAN COIL UNITS TO COMPLY WITH NFPA 90A.
REF.REF.
1
SINK (D)
2
1
3
3
3
3
1" SP (E)1" SP (E)1" SP FLUSH
VALVE (E)
1/2" SP (D)
1/2" SP (D)
2
CEILING EA
GRILLE (D)2
6x6 EA (D)
12X6 EA (D)
1/2" DCW, 1/2" DHW
RISERS (E)1/2" DCW (E)1/2" DHW (E)1-1/2" SAN (D)
4
1-1/2" SAN RISER (E)
4
2
3" SAN/VENT
RISER (E)
W.C.O.
1
2
1" SP (E)
2
3RANGE
HOOD (N)1/2" DCW (E)1/2" DHW (E)4
1/2" DCW, 1/2" DHW
RISERS WITHIN WALL (E)
5
3" SAN/VENT
RISER (E)
0 1 2 4
SCALE: 1/2"=1'-0"CORNE
LL
U N I V
E
RSI
TYFOUN
D E D 5681
AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.IPP.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER COMPLEX
BAKER COMPLEX
KITCHEN
RENOVATIONS
MP-101
11121224
BAKER TOWER
PARTIAL
FLOOR PLANS
T. FISHER
TRF
3004
December 17, 2018
MP-101 KEYED DEMOLITION NOTES
1 DISCONNECT AND REMOVE EXISTING SINK AND ASSOCIATED FAUCET/DRAIN
ASSEMBLY. REMOVE 1/2" DOMESTIC COLD WATER AND 1/2" DOMESTIC HOT WATER
BRANCH LINES BACK TO RISER. EXISTING 1/2" RISERS TO REMAIN FOR
RECONNECTION. PARTIALLY REMOVE 1-1/2" SANITARY DRAIN PIPING.
2 DISCONNECT AND REMOVE EXISTING EXHAUST FAN AND ASSOCIATED DUCTWORK,
GRILLES, AND ACCESSORIES ABOVE CEILING.
3 DISCONNECT AND REMOVE EXISTING CONCEALED SPRINKLER HEAD AND
ASSOCIATED 1/2" BRANCH PIPING BACK TO 1" MAIN. EXISTING 1" TEE TO REMAIN
FOR RECONNECTION.
4 DISCONNECT AND REMOVE PORTION OF EXISTING 1-1/2" SANITARY DRAIN BACK TO
DROP. EXISTING RISER FROM BELOW SLAB TO REMAIN FOR RECONNECTION.
MP-101 KEYED CONSTRUCTION NOTES
1 PROVIDE SINK, FAUCET, 1/2" DOMESTIC COLD, 1/2" HOT WATER SUPPLY, 1-1/2"
DRAIN, AND 1-1/4" VENT TO CABINET/COUNTER MOUNTED KITCHEN SINK.
2 PROVIDE UPRIGHT SPRINKLER HEAD. INSTALL/CONNECT TO EXISTING 1"
SPRINKLER BRANCH PIPING TEE.
3 RECIRCULATING RANGE HOOD, REFER TO ARCHITECTURAL DRAWINGS. RANGE
HOOD SHALL UTILIZE EXISTING ADJACENT NATURAL VENTILATION AS MAKE-UP AIR
SOURCE.
4 PROVIDE 1/2" COLD AND 1/2" HOT DOMESTIC WATER SUPPLY TO SINK FAUCET WITH
SUPPLY SHUTOFFS. CONNECT TO EXISTING 1/2" COLD AND 1/2" HOT DOMESTIC
WATER SUPPLY RISERS.
5 PROVIDE 1-1/2" SANITARY DRAIN WITH TRAP TO SINK PF-1. CONNECT TO EXISTING
1-1/2" SANITARY DRAIN RISER. CONTRACTOR SHALL SCOPE EXISTING SANITARY
LINE.
#
#
MP-101 GENERAL PLUMBING NOTES
1.0 EXISTING DOCUMENTATION OF THE SANITARY AND VENT SYSTEM PIPING LAYOUT
IS NOT AVAILABLE. CONTRACTOR SHALL SCOPE AND IDENTIFY EXISTING SANITARY
AND VENT PIPING IN THE VACINITY OF THE SCOPE OF WORK. PROVIDE RESULTS TO
FACILITIES ENGIEERING FOR REVIEW.
SCALE:1/2" = 1'-0"1 BASEMENT MECHANICAL/PLUMBING DEMOLITION PLAN
SCALE:1/2" = 1'-0"2 BASEMENT MECHANICAL/PLUMBING CONSTRUCTION PLAN
1 10/10/18 ISSUE FOR 50% DD REVIEW
2 11/12/18 ISSUE FOR 95% CD REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
REF.REF.REF.1 2" HHWR (E)2" HHWS (E)RADIATOR (D)1
(S) G10
(S) G09
(S) G08
1
MP-001
Sim
3
1
2
(S) G10
(S) G08
(S) G09
FCU-G09
3
1
MP-001
2 2" HHWR (E)2" HHWS (E)1FCU-G09
1 RADIATOR (D)2" HHWR (E)2" HHWS (E)1 CORNE
LL
U N I V
E
RSI
TYFOUN
D E D 5681
AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.IPP.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER COMPLEX
BAKER COMPLEX
KITCHEN
RENOVATIONS
MP-102
11121224
BAKER NORTH
AND SOUTH
GROUND
FLOOR
PARTIAL HVAC
FLOOR PLANS
T. FISHER
TRF
3004
December 17, 2018
SCALE:1/4" = 1'-0"1 SOUTH GROUND FLOOR PARTIAL HVAC DEMOLITION PLAN
SCALE:1/4" = 1'-0"2 SOUTH GROUND FLOOR PARTIAL HVAC CONSTRUCTION PLAN
SCALE:1/4" = 1'-0"4 NORTH GROUND FLOOR PARTIAL HVAC CONSTRUCTION PLAN
SCALE:1/4" = 1'-0"3 NORTH GROUND FLOOR PARTIAL HVAC DEMOLITION PLAN
MP-102 KEYED DEMOLITION NOTES
1 DISCONNECT AND REMOVE EXISTING FIN TUBE RADIATION, COVER, CONTROL
VALVE, AND THERMOSTAT. REMOVE PIPING BACK TO MAINS AND CAP.
MP-102 KEYED CONSTRUCTION NOTES
1 VERTICAL SLOPE TOP FAN COIL UNIT. MOUNT FAN COIL UNIT AND ENCLOSURE TO
STUD WALL WITH MANUFACTURERS PROVIDED BRACKETS. REFER TO SCHEDULE
FOR SPECIFICATIONS AND ACCESSORIES. REFER TO 2/M-001 FOR PIPING DETAILS.
2 RECIRCULATING RANGE HOOD, REFER TO ARCHITECTURAL DRAWINGS. RANGE
HOOD SHALL UTILIZE EXISTING ADJACENT NATURAL VENTILATION AS MAKE-UP AIR
SOURCE.
3 CONNECT 3/4" HYDRONIC HEATING SUPPLY AND RETURN TO EXISTING 2" HYDRONIC
SUPPLY AND RETURN PIPING WITH SHUTOFF VALVES. ROUTE 3/4" PIPING EXPOSED
TO DROPS WITHIN STUD WALL TO FINTUBE RADIATION ENCLOSURE.
1 10/10/18 ISSUE FOR 50% DD REVIEW
2 11/12/18 ISSUE FOR 95% CD REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
#
#
0 2 4 8
SCALE: 1/4"=1'-0"
REF.REF.REF.REF.1
MP-001
PF-1 1
4" SP (E)2" DCW (E)2" DHW (E)1" DHWR (E)2
3
1/2" DCW
DROP
1/2" DHW
DROP
3
3
4
1
4" SP (E)2" DCW (E)1" DHWR (E)1/2" DCW,
1/2" DHW
DROPS (D)2" DCW (E)1
1/2" DCW,
1/2" DHW
DROPS (D)4" SP (E)2" DHW (E)2" DCW (E)1" DHWR (E)4" SP (E)2" DHW (E)2" DCW (E)1" DHWR (E)PF-1 1
4
1/2" DCW
DROP 3
1/2" DHW
DROP 3 CORNE
LL
U N I V
E
RSI
TYFOUN
D E D 5681
AD
FACILITIES
ENGINEERING
N
ARCHIVE BAR CODEITHACA, NEW YORK
ARCH/STRUCT:
CIVIL/ENV:
ELECTRICAL:
MECHANICAL:
DATE:
FACILITY:
DESIGN:
DRAWN:
WWW.IPP.CORNELL.EDU
IT IS A VIOLATION OF NEW YORK STATE LAW FOR
ANY PERSON, UNLESS ACTING UNDER THE
DIRECTION OF A LICENSED ARCHITECT OR
ENGINEER, TO ALTER THIS DOCUMENT IN ANY
WAY. IF THIS DOCUMENT IS ALTERED, THE
ALTERING ARCHITECT OR ENGINEER SHALL AFFIX
TO SUCH DOCUMENT THEIR SEAL AND THE
NOTATION "ALTERED BY" FOLLOWED BY THEIR
SIGNATURE, THE DATE OF SUCH ALTERATION, AND
A SPECIFIC DESCRIPTION OF THE ALTERATION.
WARNING
REVISIONS
ARCHITECTURAL, STRUCTURAL,
CIVIL, ENVIRONMENTAL,
MECHANICAL, AND ELECTRICAL
ENGINEERING
201 HUMPHREYS SERVICE BLDG
ITHACA, NEW YORK 14853-3701
BAKER COMPLEX
BAKER COMPLEX
KITCHEN
RENOVATIONS
MP-103
11121224
BAKER NORTH
AND SOUTH
GROUND
FLOOR
PARTIAL
PLUMBING
FLOOR PLANS
T. FISHER
TRF
3004
December 17, 2018
SCALE:1/4" = 1'-0"4 NORTH GROUND FLOOR PARTIAL PLUMBING CONSTRUCTION PLAN
SCALE:1/4" = 1'-0"3 NORTH GROUND FLOOR PARTIAL PLUMBING DEMOLITION PLAN
MP-103 KEYED CONSTRUCTION NOTES
1 PROVIDE SINK, FAUCET, 1/2" DOMESTIC COLD, 1/2" HOT WATER SUPPLY, 1-1/2"
DRAIN, AND 1-1/4" VENT TO CABINET/COUNTER MOUNTED KITCHEN SINK.
2 RECIRCULATING RANGE HOOD, REFER TO ARCHITECTURAL DRAWINGS. RANGE
HOOD SHALL UTILIZE EXISTING ADJACENT NATURAL VENTILATION AS MAKE-UP AIR
SOURCE.
3 PROVIDE 1/2" COLD AND 1/2" HOT DOMESTIC WATER SUPPLY TO SINK FAUCET WITH
SUPPLY SHUTOFFS. CONNECT TO EXISTING 1/2" COLD AND 1/2" HOT DOMESTIC
WATER SUPPLY TAPS ON EXISTING MAINS. ROUTE PIPING WITHIN STUD WALL
DOWN TO WITHIN SINK BASE CABINET.
4 PROVIDE 1-1/2" SANITARY DRAIN WITH TRAP TO SINK PF-1. CONNECT TO EXISTING
2" SANITARY DRAIN RISER WITHIN WALL.
MP-103 KEYED DEMOLITION NOTES
1 REMOVE 1/2" DOMESTIC COLD WATER AND 1/2" DOMESTIC HOT WATER BRANCH
LINES BACK TO MAINS AND CAP. REMOVE 1-1/2" SANITARY DRAIN PIPING FROM SINK
TO WITHIN WALL AND CAP.
SCALE:1/4" = 1'-0"1 SOUTH GROUND FLOOR PARTIAL PLUMBING DEMOLITION PLAN
SCALE:1/4" = 1'-0"2 SOUTH GROUND FLOOR PARTIAL PLUMBING CONSTRUCTION PLAN
1 10/10/18 ISSUE FOR 50% DD REVIEW
2 11/12/18 ISSUE FOR 95% CD REVIEW
3 11/20/18 ISSUE FOR COORDINATED REVIEW
4 12/17/18 ISSUE FOR CONSTRUCTION
0 2 4 8
SCALE: 1/4"=1'-0"
#
#
CORNELLUNIVERS IT Y F O U NDED5681ADFACILITIESENGINEERINGARCHIVE BAR CODEITHACA, NEW YORKARCH/STRUCT:CIVIL/ENV:ELECTRICAL:MECHANICAL:DATE:FACILITY:DESIGN:DRAWN:WWW.FCS.CORNELL.EDUIT IS A VIOLATION OF NEW YORK STATE LAW FOR ANY PERSON, UNLESS ACTING UNDER THE DIRECTION OF A LICENSED ARCHITECT OR ENGINEER, TO ALTER THIS DOCUMENT IN ANY WAY. IF THIS DOCUMENT IS ALTERED, THE ALTERING ARCHITECT OR ENGINEER SHALL AFFIX TO SUCH DOCUMENT THEIR SEAL AND THE NOTATION "ALTERED BY" FOLLOWED BY THEIR SIGNATURE, THE DATE OF SUCH ALTERATION, AND A SPECIFIC DESCRIPTION OF THE ALTERATION.WARNINGREVISIONSARCHITECTURAL, STRUCTURAL, CIVIL, ENVIRONMENTAL, MECHANICAL, AND ELECTRICAL ENGINEERING201 HUMPHREYS SERVICE BLDGITHACA, NEW YORK 14853-3701BAKER COMPLEXBAKER COMPLEXKITCHENRENOVATIONSE-001.GENERALNOTES ANDSYMBOLLEGENDSE.REICHARDETR3004DECEMBER 17, 2018ELECTRICAL SUBMITTAL SCHEDULEMATERIALSCHEDULE/SHOPDWGS.PRODUCTDATASAMPLESINSPECTIONS& TESTSO&M DATA WARRANTIESPANELBOARDS XLIGHT FIXTURES AND LIGHTING CONTROL XWIRING DEVICES XCONDUCTORS XRACEWAYSXFIRE ALARMXLUMINAIRE SCHEDULETYPE DESCRIPTION MOUNTING SIZE MANUFACTURER CATALOG NO. VOLTAGE LAMPS WATTAGE FINISHA2 LED UNDERCABINET FIXTURE SURFACE 12" ECOSENSE SCDM1235MULT 120-277VLED 4 WHITEA3 LED INDIIRECT FIXTURE PENDANT 1x8 FINELITE S12-LED-ID-WCB-8-2E-S-835-OPEN-120V-SC-FA-FE-C4-OBO120V LED 23 WHITEA3E LED INDIIRECT FIXTURE PENDANT 1x8 FINELITE S12-LED-ID-WCB-8-2E-S-835-OPEN-120V-SC-FA-FE-C4-OBO W/ EM DRIVER120V LED 23 WHITEA4 LED INDIIRECT FIXTURE PENDANT 1x4 FINELITE S12-LED-ID-WCB-4-3E-SS-835-OPEN-120V-SC-FA-FE-C4-OBO120V LED 23 WHITEA5 LED INDIIRECT FIXTURE PENDANT 1x4 FINELITE S12-LED-ID-WCB-4-3E-HH-8-35-OPEN-120V-SC-FA-FE-C4-OBO120V LED 44 WHITEA5E LED INDIIRECT FIXTURE PENDANT 1x8 FINELITE S12-LED-ID-WCB-8-3E-HH-8-35-OPEN-120V-SC-FA-FE-C4-OBO W/EM DRIVER120V LED 44 WHITEGENERAL ELECTRICAL NOTES1.0 ELECTRICAL SCHEMATICS INDICATED ON CONTRACT DOCUMENTS AREDIAGRAMMATIC. IT IS NOT THE INTENT TO SHOW EXACT OR MOST EFFICIENTROUTING. VERIFY ALL DIMENSIONS AND FIELD CONDITIONS ON SITE. ANYCONFLICTS BETWEEN CONSTRUCTION DOCUMENTS AND FIELD CONDITIONS SHALLBE BROUGHT TO CORNELL'S PROJECT MANAGER FOR RESOLUTION BEFORE WORKPROCEEDS.2.0 ASSURE PUBLIC AND WORKER SAFETY AT ALL TIMES. PROTECT ADJOINING AREASFROM DAMAGE AND DUST. REMOVE ALL DEBRIS FROM SITE AND DISPOSE OFWASTE MATERIAL IN A SAFE MANNER. KEEP THE PREMISES FREE OF DEBRIS FROMTHE EXECUTION OF WORK. DELIVER A FINAL PRODUCT THAT IS CLEAN ANDOPERABLE.3.0 FIRE STOP ELECTRICAL PENETRATIONS THROUGH FIRE RATED WALLS AND/ORFLOORS WITH MATERIAL EQUAL IN RATING TO THE CONSTRUCTION OF THEMATERIAL PENETRATED.4.0 WORK SHALL BE COMPLETED AS SPECIFIED AND INDICATED ON CONTRACTDOCUMENTS. ANY SUGGESTED ALTERNATE MANUFACTURER OR METHOD OFINSTALLATION SHALL BE SUBMITTED TO PROJECT ENGINEER FOR APPROVALPRIOR TO ORDERING ANY MATERIALS OR COMMENCING EXECUTION OF WORK.5.0 GROUNDING SHALL BE IN STRICT ACCORDANCE WITH NEC ARTICLE 250. PROVIDEEQUIPMENT GROUND CONDUCTOR WITH EACH BRANCH CIRCUIT INDICATED ONCONTRACT DOCUMENTS. EQUIPMENT GROUND CONDUCTOR SHALL BE ROUTEDWITH ASSOCIATED PHASE CONDUCTORS.6.0 PROVIDE A NEW TYPED PANELBOARD DIRECTORY FOR EACH PANELBOARD. LABELALL NEW DEVICE FACEPLATES WITH SOURCE AND CIRCUIT NUMBER. PROVIDEPERMANENT LABEL ON SWITCHING DEVICES INDICATING EQUIPMENT SERVICE ANDINVENTORY NUMBERS. COORDINATE EQUIPMENT INVENTORY NUMBERS WITHCORNELL UNIVERSITY'S MECHANICAL SHOP, 255-8667.7.0 CIRCUITS RATED 20-AMP, 120 VOLT SHALL CONTAIN SEPARATE NEUTRALCONDUCTORS.8.0 CONDUCTORS SHALL BE A MINIMUM OF 12AWG, STRANDED COPPER, 600VAC, 90DEGREE C, TYPE THHN/THWN-2 FOR DRY AREAS AND XHHW/THWN-2 FOR WETAREAS.9.0 CONDUITS SHALL BE A MINIMUM OF 3/4 INCHES DIAMETER. CONDUITS SHALL BEELECTRICAL METALLIC TUBING (EMT) AND SURFACE MOUNTED UNLESS NOTEDOTHERWISE.10.0 AIC RATING OF NEW CIRCUIT BREAKERS SHALL MATCH RATING OF RESPECTIVEPANELBOARD. SIZE AS INDICATED.11.0 PROVIDE PULL STRING THROUGH NEW CONDUIT AND BOXES. PROVIDE SUPPORTHANGERS FOR CONDUIT AS NEEDED.12.0 INSTALL RACEWAY SYSTEMS ENSURING PROPER ACCESS TO EQUIPMENT ANDDEVICES AND WITH SUFFICIENT SPACE TO PERFORM ROUTINE MAINTENANCE ANDREPAIR. RACEWAYS THAT ARE NOT INSTALLED WITH THIS REQUIREMENT IN MINDSHALL BE RELOCATED AT NO EXPENSE TO THE UNIVERSITY UNTIL DEFICIENCIESARE CORRECTED.ELECTRICAL SCOPE OF WORK1.0 PROVIDE POWER AND LIGHTING UPGRADES FOR THE KITCHEN RENOVATIONS INNORTH BAKER, SOUTH BAKER AND BAKER TOWER.ELECTRICAL LEGENDLIGHTING LEGENDMOTOR1'x4' LUMINAIREHARDWIRED EQUIPMENT CONNECTIONP-1A12HOMERUN TO PANEL P-1A, CIRCUIT #12. FED FROM 20A -1P BREAKER IS INTENDED UNLESS NOTED OTHERWISE. RUN GREEN WIRE GROUND FOR ALL CIRCUITS. PROVIDE ONE GROUND PER CIRCUIT.EMERGENCY POWER OFF (EPO)GROUND ROD ELECTRODEDUPLEX RECEPTACLE WITH GFCI PROTECTIONDUPLEX RECEPTACLE WITH AFCI PROTECTIONQUAD RECEPTACLELINETYPES LEGENDSPECIAL RECEPTACLE5-30RPANELBOARDJUNCTION BOXB = INSTALLED IN BASEBOARDTR = INSTALLED IN WOOD TRIM/CASEWORK/WAINSCOTTSR = SURFACE RACEWAYWP = WEATHERPROOFAC = AIR CONDITIONERXDUPLEX RECEPTACLE: DOUBLE DUPLEX RECEPTACLEMOTOR STARTERJ2'x4' LUMINAIRECEILING MOUNTED LUMINAIREEM LIGHTING BATTERY UNITCOMBO EXIT SIGN/EM LIGHTING BATTERY UNITSINGLE FACE, WALL MOUNT EXIT SIGNDOUBLE FACE, WALL MOUNT EXIT SIGNSINGLE FACE, CEILING MOUNT EXIT SIGNDOUBLE FACE, CEILING MOUNT EXIT SIGNLIGHT SWITCH:SAFETY SWITCH (NON-FUSED)SAFETY SWITCH (FUSED)X3 = 3-WAY SWITCH4 = 4-WAY SWITCHD = DIMMER SWITCHO = WALL SWITCH OCCUPANCY SENSORV = WALL SWITCH VACANCY SENSORW = WIRELESS SWITCHS = WIRELESS SCENE SWITCHWIRELESS OCCUPANCY SENSORWIRELESS DAYLIGHT SENSOROSWDS1'x2' LUMINAIREFIRE ALARM LEGENDFIRE ALARM CONTROL PANELBATTERY CABINETWATER FLOW SWITCHMUXPADREMOTE ANNUNCIATORD = DUCT SMOKE DETECTORR = RELAY BASEBR = BEAM RECEIVERBT = BEAM TRANSMITTERSB = SOUNDER BASESMOKE DETECTOR: TAMPER SWITCHAUDIBLE NOTIFICATION APPLIANCEFACPBATTMUXFAANAC PANELNACMANUAL PULL STATIONFSXF = FIXED TEMPERATURER = RATE OF RISER/F = COMBINATION RISE/FIXED TEMPERATUREHEAT DETECTOR: HXCARBON MONOXIDE DETECTORCOAMFXXcdCFSFSXXcdCTSADDRESSABLE MODULEXXcd = CANDELAC = CEILINGCOMBO A/V NOTIFICATION APPLIANCE: XXcd = CANDELAC = CEILINGVISUAL NOTIFICATION APPLIANCE:SUPPRESSION SYSTEMELECTRICAL ABBREVIATIONSAC AIR CONDITIONERAFF ABOVE FINISHED FLOORAFG ABOVE FINISHED GRADEAFI ARC FAULT INTERRUPTERAMM ADDRESSABLE MONITOR MODULEAOM ADDRESSABLE OUTPUT MODULEARB AUXILIARY RELAY BOARDATS AUTOMATIC TRANSFER SWITCHB BASEBOARDBKR BREAKERC CONDUITCD CANDELACKT CIRCUITCR CONTROL RELAYEC ELECTRICAL CONTRACTOREMT ELECTRICAL METALLIC TUBINGEPO EMERGENCY POWER OFF STATIONFAA FIRE ALARM ANNUNCIATOR PANELFACP FIRE ALARM CONTROL PANELFSD FIRE SMOKE DAMPERGAA GENERATOR ALARM ANNUNCIATORGFI GROUND FAULT INTERRUPTERGND GROUNDHP HORSEPOWERKW KILOWATTLC LIGHTING CONTACTORLFMC LIQUID TIGHT FLEXIBLE METALLIC CONDUITLTG LIGHTINGMCB MAIN CIRCUIT BREAKERMLO MAIN LUG ONLYMTS MANUAL TRANSFER SWITCHNAC NOTIFICATION APPLIANCE CIRCUITNIC NOT IN CONTRACTOE OVERHEAD ELECTRICPC PHOTOCELLPM PLUGMOLDPP POWER PANELPVC POLYVINYL CHLORIDE CONDUITRGS RIGID GALVANIZED STEEL CONDUITSR SURFACE RACEWAYST SHUNT TRIPTM THERMAL MAGNETICTR TRIM/CASEWORK/WAINSCOTTTSP TWISTED SHIELDED PAIRTYP TYPICALUE UNDERGROUND ELECTRICUON UNLESS OTHERWISE NOTEDUPS UNINTERRUPTIBLE POWER SUPPLYVVOLTSVA VOLT AMPSWP WATERPROOFUNDERGROUND ELECTRICUEUNDERGROUND LIGHTINGULOVERHEAD ELECTRICOETO BE PROVIDEDDEMOLITION / TO BE RELOCATEDEXISTING TO REMAINUNDERGROUND TELCOUCMOUNTING HEIGHTSCARD READER 48" TOP OF BOXLIGHT SWITCH 48" TOP OF BOXRECEPTACLE 18" TOP OF BOXDATA OUTLET 18" TOP OF BOXTV OUTLET 84" TOP OF BOXPHONE OUTLET 48" TOP OF BOXSAFETY SWITCH 60" CENTERLINE OF HANDLEMOTOR STARTER 60" CENTERLINE OF HANDLEPANELBOARD 72" TOP OF PANELBOARDMANUAL PULL STATION 48" OPERABLE HANDLENOTIFICATION APPLIANCE 80" BOTTOM OF LENSDOOR HOLD OPEN COORDINATE IN FIELDEM BATTERY UNIT 96" BOTTOM OF UNITEM REMOTE UNIT 102" BOTTOM OF UNITEXIT SIGN 96" BOTTOM OF UNITLIGHT POLE WITH LED LUMINAIRES, REFER TO PLANS FOR NUMBER AND CONFIGURATION OFHEADSGENERAL ELECTRICAL DEMOLITION NOTES1.0 ELECTRICAL EQUIPMENT SHOWN DASHED ON DEMOLITION DRAWINGS, INCLUDINGASSOCIATED ANCHORS, SUPPORTS, STRAPS, BOXES, FITTINGS, AND OTHERAPPURTENANCES NOT SHOWN, SHALL BE DISCONNECTED AND REMOVED.REMOVE ASSOCIATED BRANCH CIRCUITRY TO SOURCE, UNLESS NOTEDOTHERWISE.2.0 EXISTING RACEWAYS AND DEVICE BACKBOXES NOT INTERFERRING WITH NEWWORK SHALL BE REUSED WHERE POSSIBLE.3.0 PROVIDE JUNCTION BOXES, RACEWAYS, AND WIRING TO MODIFY/EXTEND EXISTINGSYSTEMS AND CIRCUITS FED DOWNSTREAM OF ELECTRICAL EQUIPMENT SHOWNTO BE DEMOLISHED.4.0 CUT DEMOLISHED CONDUITS INSTALLED THRU WALLS AND FLOORS FLUSH WITHTHE SURFACE AND PATCH PENETRATIONS (FIRESTOP IF LOCATED ON A FIRERATED SURFACE). PATCH AND PAINT SURFACES IN EXPOSED AREAS TO MATCHSURROUNDING MATERIALS, FINISHES, AND COLORS.5.0 PROVIDE BLANK COVERPLATES ON UNUSED BACKBOXES REMAINING FROMDEMOLITION NOT SPECIFIED TO BE INFILLED.6.0 EXISTING EQUIPMENT SHOWN TO REMAIN SHALL BE PROTECTED DURINGCONSTRUCTION.1 10/11/18 ISSUE FOR DD REVIEW2 11/12/18 ISSUE FOR 95% REVIEW3 11/20/18 ISSUE FOR COORDINATED REVIEW4 12/17/18 ISSUE FOR CONSTRUCTION
208V50AGFIHFGFIGFI33GFIDEF123945168677777SSSFPANEL A NORTHFSSSPANEL A SOUTHCORNELLUNIVERS IT Y F O U NDED5681ADFACILITIESENGINEERINGNARCHIVE BAR CODEITHACA, NEW YORKARCH/STRUCT:CIVIL/ENV:ELECTRICAL:MECHANICAL:DATE:FACILITY:DESIGN:DRAWN:WWW.FCS.CORNELL.EDUIT IS A VIOLATION OF NEW YORK STATE LAW FOR ANY PERSON, UNLESS ACTING UNDER THE DIRECTION OF A LICENSED ARCHITECT OR ENGINEER, TO ALTER THIS DOCUMENT IN ANY WAY. IF THIS DOCUMENT IS ALTERED, THE ALTERING ARCHITECT OR ENGINEER SHALL AFFIX TO SUCH DOCUMENT THEIR SEAL AND THE NOTATION "ALTERED BY" FOLLOWED BY THEIR SIGNATURE, THE DATE OF SUCH ALTERATION, AND A SPECIFIC DESCRIPTION OF THE ALTERATION.WARNINGREVISIONSARCHITECTURAL, STRUCTURAL, CIVIL, ENVIRONMENTAL, MECHANICAL, AND ELECTRICAL ENGINEERING201 HUMPHREYS SERVICE BLDGITHACA, NEW YORK 14853-3701BAKER COMPLEXBAKER COMPLEXKITCHENRENOVATIONSE-101.ELECTRICALREMOVALPLANSE.REICHARDETR3004DECEMBER 17, 2018#E-101 KEYED DEMOLITION NOTES1 DISCONNECT AND REMOVE RECEPTACLES AT COUNTER TOP. REMOVE CONDUITAND CONDUCTORS BACK TO KITCHEN LOAD CENTER.2 DISCONNECT AND REMOVE RECEPTACLE UNDER SINK. REMOVE CONDUIT ANDCONDUCTORS BACK TO KITCHEN LOAD CENTER.3 DISCONNECT AND REMOVE RANGE RECEPTACLE. REMOVE CONDUIT ANDCONDUCTORS BACK TO KITCHEN LOAD CENTER.4 DISCONNECT AND REMOVE REFRIGERATOR RECEPTACLE. REMOVE CONDUIT ANDCONDUCTORS BACK TO KITCHEN LOAD CENTER.5 DISCONNECT AND REMOVE EXHAUST FAN POWER AND SWITCH. REMOVE CONDUITAND CONDUCTORS BACK TO KITCHEN LOAD CENTER.6 DISCONNECT AND REMOVE LIGHT FIXTURES AND SWITCH. REMOVE CONDUIT ANDCONDUCTORS BACK TO SOURCE.7 DISCONNECT AND REMOVE LIGHT FIXTURES AND SWITCHES. REMOVE CONDUITAND CONDUCTORS BACK TO EXISTING JUNCTION BOXES ON CEILING AND SAVEFOR REUSE.8 DISCONNECT AND REMOVE HEAT DETECTOR. SAVE CIRCUIT FOR REUSE.9 DISCONNECT AND REMOVE KITCHEN LOAD CENTER. REMOVE FEED BACK TOJUNCTION BOX SPLICE(FORMER MDP).10 DISCONNECT AND REMOVE RECEPTACLE AT FLOOR LEVEL. REMOVE CONDUIT ANDCONDUCTORS BACK TO KITCHEN LOAD CENTER.11 DISCONNECT AND REMOVE EXISTING DATA JACKS. PROVIDE 4”X4” COVER ONEXISTING DATA JUNCTION BOX AND SAVE EXISTING DATA WIRING FOR REUSE TOEXTEND TO NEW VENDING MACHINE LOCATION. COORIDATE WITH CIT.12 DISCONNECT AND REMOVE KITCHEN LOAD CENTER AND BACKBOX. REMOVEEXISTING CONDUCTORS BACK TO EXISTING SPLICE IN JUNCTION BOX INELECTRICAL ROOM. TAG AND SAVE FEEDER CONDUCTORS FROM MDP-1 FORREUSE TO FEED NEW PANEL.024 8SCALE: 1/4"=1'-0"SCALE:1/4" = 1'-0"1BAKER TOWER BASEMENT POWER REMOVAL PLANSCALE:1/4" = 1'-0"2BAKER TOWER BASEMENT LIGHTING AND FIRE ALARM REMOVAL PLANSCALE:1/4" = 1'-0"3NORTH BAKER BASEMENT REMOVAL PLANS777777777777721SCALE:1/4" = 1'-0"4SOUTH BAKER 1ST FLOOR REMOVAL PLANS717777777710111021112121 10/11/18 ISSUE FOR DD REVIEW2 11/12/18 ISSUE FOR 95% REVIEW3 11/20/18 ISSUE FOR COORDINATED REVIEW4 12/17/18 ISSUE FOR CONSTRUCTION
F208V50ADOCDHS208V50A208V50ADDD33DD33DFDOCDDDHSKITCHEN PANEL LPP-G1JUNCTION BOX314522PANEL ANORTH225410143111213FCU-G0910141042253PANEL ASOUTH121113FCU-G091066677SSSFA3A3A5EA5A4A2A26677A3A3A5EA5A4A2A2FSSSA-5E96786A-3A-3A-3EA-3A-2A-2A-2666E-102 KEYED CONSTRUCTION NOTES1 PROVIDE 100 AMP, MLO PANEL IN LOCATION INDICATED. PROVIDE 3-#6 & 1-#6G IN 1'EMT FROM JUNCTION BOX SPLICE.2 PROVIDE NEMA 5-20R RECEPTACLE 6” ABOVE COUNTERTOP IN LOCATIONINDICATED.PROVIDE 2-#12 & 1-#12 GND (THHN) FROM 20A BREAKER IN PANEL TORECEPTACLES. PROVIDE SURFACE RACEWAY FROM PANEL TO THE NEW WALL.PROVIDE 3/4” EMT BEHIND WALL TO RECEPTACLES. REFER TO PANEL SCHEDULESFOR COUNTERTOP CIRCUITING.3 PROVIDE NEMA 5-20R RECEPTACLE INSIDE TOP CABINET FOR MICROWAVE POWER.PROVIDE 2-#12 & 1-#12 GND (THHN) FROM 20A BREAKER IN PANEL TO RECEPTACLE.PROVIDE SURFACE RACEWAY FROM PANEL TO THE NEW WALL. PROVIDE 3/4” EMTBEHIND WALL TO RECEPTACLE.REFER TO PANEL SCHEDULE FOR CIRCUITING.4 PROVIDE NEMA 14-50R RECEPTACLE FOR RANGE AT 18” AFF IN LOCATIONINDICATED. PROVIDE 3-#8 & 1-#10G IN ¾” EMT FROM PANEL TO RANGERECEPTACLE. REFER TO PANEL SCHEDULE FOR CIRCUITING.5 PROVIDE NEMA 5-20R RECEPTACLE AT 18” AFF IN LOCATION INDICATED FORREFIGERATOR.PROVIDE 2-#12 & 1-#12 GND (THHN) FROM 20A BREAKER IN PANEL TORECEPTACLE. PROVIDE SURFACE RACEWAY FROM PANEL TO THE NEW WALL.PROVIDE 3/4” EMT BEHIND WALL TO RECEPTACLE. REFER TO PANEL SCHEDULEFOR CIRCUITING.6 PROVIDE LIGHT FIXTURE IN LOCATION INDICATED. PENDANT MOUNT FIXTURE FROMCEILING AT 8' AFF. FOR 3-WAY CIRCUITS, PROVIDE LEVITON CAT NO. IP710LFZDIMMING SWITCH AT EXISTING SWITCH LOCATION AT ONE END AND LEVITON#5622-2W 3-WAY SWITCH AT THE OTHER. PROVIDE DIMMING SWITCH ONLY FOR THEBAKER TOWER LOUNGE AND LIGHTS IN FRONT OF VENDING MACHINES. PROVIDELOW VOLTAGE WIRING FOR DIMMING. CONNECT TO CIRCUITING SAVED FROMREMOVALS.7 PROVIDE UNDER CABINET FIXTURE IN LOCATION INDICATED. PROVIDE SENSORSWITCH CAT NO. SPODMRD DIMMER SWICH AT 6" ABOVE COUNTERTOPBACKSPLASH. CONNECT TO LIGHTING CIRCUIT SAVED FROM REMOVALS. PROVIDESURFACE RACEWAY FROM LIGHTING JUNCTION BOX ON CEILING TO WALL ANDPROVIDE 3/4" EMT BEHIND WALL.8 PROVIDE HEAT DETECTOR IN LOCATION INDICATED. RECONNECT TO EXISTINGCIRCUIT SAVED FROM REMOVALS.9 PROVIDE 75CD FIRE ALARM STROBE AT 84" IN LOCATION INDICATED. PROVIDE 2-#14IN 3/4" EMT FROM EXISTING FIRE ALARM STROBE CIRCUIT IN LOUNGE AND EXTENDNOTIFICATION CIRUIT FOR NEW DEVICE.10 PROVIDE NEMA 5-20R RECEPTACLE 6” ABOVE COUNTERTOP IN LOCATIONINDICATED.PROVIDE 2-#12 & 1-#12 GND (THHN) FROM 20A BREAKER IN PANEL TORECEPTACLES. PROVIDE SURFACE RACEWAY FROM PANEL TO THE NEW WALL.PROVIDE 3/4” EMT BEHIND WALL TO RECEPTACLE. REFER TO PANEL SCHEDULESFOR COUNTERTOP CIRCUITING.11 PROVIDE DATA JACKS IN NEW LOCATION FOR VENDING MACHINES. PROVIDE NEWCAT6 FROM WIRING SAVED FROM REMOVAL TO NEW LOCATION. COORDINATE ALLWORK WITH CIT.12 PROVIDE 100 AMP, SEMI-RECESSED MAIN BREAKER PANEL IN LOCATION INDICATED.CONNECT ALL BRANCH CIRCUITS AND FEEDER CABLES SAVED FROM REMOVALS.REFER TO PANEL SCHEDULE ON E-501 FOR ADDITIONAL INFORMATION.13 PROVIDE 2-#12 & 1-#12 GND (THHN) FROM 20A BREAKER IN PANEL TO THE CABINETHEATER. PROVIDE SURFACE RACEWAY FROM PANEL TO THE NEW WALL. PROVIDE3/4” EMT BEHIND WALL TO THE CABINET HEATER. REFER TO PANEL SCHEDULE FORCIRCUITING.14 PROVIDE DEDICATED NEMA 5-20R RECEPTACLE 18” ABOVE FLOOR FOR EACHVENDING MACHINE IN LOCATION INDICATED.PROVIDE 2-#12 & 1-#12 GND (THHN)FROM 20A BREAKER IN PANEL TO RECEPTACLE. PROVIDE SURFACE RACEWAYFROM PANEL TO RECEPTACLE.REFER TO PANEL SCHEDULE FOR CIRCUITING.#SCALE: 3/16"=1'-0"024612CORNELLUNIVERS IT Y F O U NDED5681ADFACILITIESENGINEERINGNARCHIVE BAR CODEITHACA, NEW YORKARCH/STRUCT:CIVIL/ENV:ELECTRICAL:MECHANICAL:DATE:FACILITY:DESIGN:DRAWN:WWW.FCS.CORNELL.EDUIT IS A VIOLATION OF NEW YORK STATE LAW FOR ANY PERSON, UNLESS ACTING UNDER THE DIRECTION OF A LICENSED ARCHITECT OR ENGINEER, TO ALTER THIS DOCUMENT IN ANY WAY. IF THIS DOCUMENT IS ALTERED, THE ALTERING ARCHITECT OR ENGINEER SHALL AFFIX TO SUCH DOCUMENT THEIR SEAL AND THE NOTATION "ALTERED BY" FOLLOWED BY THEIR SIGNATURE, THE DATE OF SUCH ALTERATION, AND A SPECIFIC DESCRIPTION OF THE ALTERATION.WARNINGREVISIONSARCHITECTURAL, STRUCTURAL, CIVIL, ENVIRONMENTAL, MECHANICAL, AND ELECTRICAL ENGINEERING201 HUMPHREYS SERVICE BLDGITHACA, NEW YORK 14853-3701BAKER COMPLEXBAKER COMPLEXKITCHENRENOVATIONSE-102.ELECTRICALINSTALLATIONPLANSE.REICHARDETR3004DECEMBER 17, 2018SCALE:3/16" = 1'-0"1BAKER TOWER POWER INSTALLATIONSCALE:3/16" = 1'-0"2NORTH BAKER POWER PLANSCALE:3/16" = 1'-0"5SOUTH BAKER POWER PLANSCALE:3/16" = 1'-0"3NORTH BAKER LIGHTING PLANSCALE:3/16" = 1'-0"6SOUTH BAKER LIGHTING PLANSCALE:3/16" = 1'-0"4BAKER TOWER LIGHTING INSTALLATION1 10/11/18 ISSUE FOR DD REVIEW2 11/12/18 ISSUE FOR 95% REVIEW3 11/20/18 ISSUE FOR COORDINATED REVIEW4 12/17/18 ISSUE FOR CONSTRUCTION
CORNELLUNIVERS IT Y F O U NDED5681ADFACILITIESENGINEERINGARCHIVE BAR CODEITHACA, NEW YORKARCH/STRUCT:CIVIL/ENV:ELECTRICAL:MECHANICAL:DATE:FACILITY:DESIGN:DRAWN:WWW.FCS.CORNELL.EDUIT IS A VIOLATION OF NEW YORK STATE LAW FOR ANY PERSON, UNLESS ACTING UNDER THE DIRECTION OF A LICENSED ARCHITECT OR ENGINEER, TO ALTER THIS DOCUMENT IN ANY WAY. IF THIS DOCUMENT IS ALTERED, THE ALTERING ARCHITECT OR ENGINEER SHALL AFFIX TO SUCH DOCUMENT THEIR SEAL AND THE NOTATION "ALTERED BY" FOLLOWED BY THEIR SIGNATURE, THE DATE OF SUCH ALTERATION, AND A SPECIFIC DESCRIPTION OF THE ALTERATION.WARNINGREVISIONSARCHITECTURAL, STRUCTURAL, CIVIL, ENVIRONMENTAL, MECHANICAL, AND ELECTRICAL ENGINEERING201 HUMPHREYS SERVICE BLDGITHACA, NEW YORK 14853-3701BAKER COMPLEXBAKER COMPLEXKITCHENRENOVATIONSE-501.PANELSCHEDULESE.REICHARDETR3004DECEMBER 17, 2018TOTAL DEMAND AMPS:0 ATOTAL CONN AMPS:0 ATOTAL DEMAND:0 VATOTAL CONN LOAD:0 VALOAD CLASSIFICATION CONN LOAD DEMAND FACTOR EST DEMAND PANEL TOTALSTOTAL AMPS:0 A 0 ATOTAL LOAD:0 VA 0 VA2324212219201718151613 SPARE 20 1 0 0 1 20 SPARE 1411 SPARE 20 1 0 0 1 20 SPARE 129 SPARE 20 1 0 0 1 20 SPARE 107 SPARE 20 1 0 0 1 20 SPARE 85 COUNTERTOP RECEPTACLES 20 1 0 01 20 REFRIGERATOR RECEPTACLE 63 -- -- -- 0 0 1 20 MICROWAVE RECEPTACLE 41 RANGE 20 2 0 0 1 20 LIGHTING 2CKT DESCRIPTION TRIP POLES A B POLES TRIP DESCRIPTION CKTENCLOSURE:NEMA 1MOUNTING:SURFACEWIRES:3MAINS RATING:100 AFED FROM: PHASE:1MAINS TYPE:MLOLOCATION:Room B08VOLTS:120/240VAIC RATING:10,000 AMPSPANEL LPP-G1TOTAL DEMAND AMPS:0 ATOTAL CONN AMPS:0 ATOTAL DEMAND:0 VATOTAL CONN LOAD:0 VALOAD CLASSIFICATION CONN LOAD DEMAND FACTOR EST DEMAND PANEL TOTALSTOTAL AMPS:0 A 0 ATOTAL LOAD:0 VA 0 VA29 -- -- -- 0 0 -- -- -- 3027 -- -- -- 0 0 -- -- -- 2825 PANEL A-1 60 3 0 0 3 100 MAIN 2623 -- -- -- 0 0 -- -- -- 2421 -- -- -- 0 0 2 20 ATTIC EX FAN FOR BATHS 2219 3PH MOTORS MECH RM 40 3 0 0 1 20 SPARE 2017 SPARE 20 1 0 0 1 20 SPARE 1815 VENDING MACHINE 20 1 0 0 1 20 SPARE 1613 VENDING MACHINE 20 1 0 0 1 20 COUNTERTOP RECEPTACLES 1411 REC 20 1 0 0 1 20 REFRIGERATOR 129 AIR DRYER 20 1 0 0 1 20 HAND DRYER BATH 107 -- -- -- 0 0 1 20 COUNTERTOP RECEPTACLES 85 AIR COMPRESSOR 20 2 0 0 1 20 MICROWAVE 63 SPARE 20 1 0 0 -- -- -- 41 CABINET HEATER 20 1 0 0 2 50 RANGE 2CKT DESCRIPTION TRIP POLES A B POLES TRIP DESCRIPTION CKTENCLOSURE:NEMA 1MOUNTING:SURFACEWIRES:4MAINS RATING:100 AFED FROM: PHASE:3MAINS TYPE:MAIN BREAKERLOCATION:Room (N) G09VOLTS:208Y/120VAIC RATING:10,000 AMPSPANEL PANEL A NORTHTOTAL DEMAND AMPS:0 ATOTAL CONN AMPS:0 ATOTAL DEMAND:0 VATOTAL CONN LOAD:0 VALOAD CLASSIFICATION CONN LOAD DEMAND FACTOR EST DEMAND PANEL TOTALSTOTAL AMPS:0 A 0 A 0 ATOTAL LOAD:0 VA 0 VA 0 VA29 -- -- -- 0 0 -- -- -- 3027 -- -- -- 0 0 -- -- -- 2825 HEAT 40 3 0 0 3 100 MAIN 2623 -- -- -- 0 0 -- -- -- 2421 RANGE 50 2 0 0 2 20 AIR COMPRESSOR 2219 STAIRWAY HEATER EAST 20 1 0 0 -- -- -- 2017 MICROWAVE 20 1 0 0 2 30 DRYER BASEMENT 1815 KITCHEN DINING LIGHTS 20 1 0 0 1 20 HAND DRYER BATH 1613 EXISTING LOAD 20 1 0 0 1 20 STAIRWELL HEATERS WEST 1411 EXISTING LOAD 20 1 0 0 1 20 DSC 8500 UPS REC 129 COUNTERTOP RECEPTACLES 20 1 0 0 1 20 HW DISPENSER 107 COUNTERTOP RECEPTACLES 20 1 0 0 1 20 VENDING MACHINE 85 SPARE 20 1 0 0 1 20 VENDING MACHINE 63 REFRIGERATOR 20 1 0 0 1 20 SPARE 41 CABINET HEATER 20 1 0 0 1 20 SPARE 2CKT DESCRIPTION TRIP POLES A B C POLES TRIP DESCRIPTION CKTENCLOSURE:Type 1MOUNTING:SurfaceWIRES:4MAINS RATING:100 AFED FROM: PHASE:3MAINS TYPE:MAIN BREAKERLOCATION:Room (S) G09VOLTS:208Y/120VAIC RATING:10,000 AMPSPANEL PANEL A SOUTH1 10/11/18 ISSUE FOR DD REVIEW2 11/12/18 ISSUE FOR 95% REVIEW3 11/20/18 ISSUE FOR COORDINATED REVIEW4 12/17/18 ISSUE FOR CONSTRUCTION