HomeMy WebLinkAbout122McGraw.Project Manual.Radon Kitchen.16018CORNELL UNIVERSITY SECTION 00 00 00
Ithaca, New York TABLE OF CONTENTS
122 McGRAW PLACE TABLE OF CONTENTS 00 00 00 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
TABLE OF CONTENTS
DIVISION 2 EXISTING CONDITIONS
02 41 19 SELECTIVE DEMOLITION
DIVISION 6 WOOD, PLASTICS, AND COMPOSITES
06 64 00 PLASTIC PANELING
DIVISION 7 THERMAL AND MOISTURE PROTECTION
07 92 00 JOINT SEALANTS
DIVISION 9 FINISHES
09 30 13 CERAMIC TILING
09 51 13 ACOUSTICAL PANEL CEILINGS
09 91 00 PAINTING
DIVISON 21 FIRE SUPPRESSION
21 05 80 FIRESTOPPING
21 10 00 FIRE PROTECTION
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING
23 00 00 GENERAL PROVISIONS FOR MECHANICAL WORK
23 05 23 VALVES
23 05 29 SUPPORTS
23 21 00 PIPE AND PIPE FITTINGS
DIVISION 26 ELECTRICAL
26 00 00 GENERAL PROVISIONS FOR ELECTRICAL WORK
26 05 19 WIRE AND CABLE
26 05 29 SUPPORTING DEVICES
26 05 33 RACEWAYS, FITTINGS AND ACCESSORIES
26 05 34 DEVICE AND JUNCTION BOXES
26 05 80 FIRESTOPPING FOR ELECTRICAL SYSTEMS
DIVISION 28 COMMUNICATIONS
28 30 01 FIRE ALARM SYSTEM - ADDRESSABLE
END OF TABLE OF CONTENTS
CORNELL UNIVERSITY SECTION 02 41 19
Ithaca, New York SELECTIVE DEMOLITION
122 McGRAW PLACE - SELECTIVE DEMOLITION 02 41 19 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 02 41 19 - SELECTIVE DEMOLITION
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of selective demolition shown on
the Drawings or called for in the Project Manual including but not limited to:
1. Demolition and removal of selected portions of building or structure.
2. Salvage of existing items to be reinstalled.
B. Related Requirements:
1. Section 01 32 33 “Photographic Documentation” for pre-demolition photos.
1.2 MATERIALS OWNERSHIP
A. Unless otherwise indicated, demolition waste becomes property of Contractor.
B. Historic items, relics, antiques, and similar objects including, but not limited to, cornerstones
and their contents, commemorative plaques and tablets, and other items of interest or value to
Owner that may be uncovered during demolition remain the property of Owner.
1. Carefully salvage in a manner to prevent damage and promptly return to Owner.
1.3 FIELD CONDITIONS
A. Owner will occupy portions of building immediately adjacent to selective demolition area.
Conduct selective demolition so Owner's operations will not be disrupted.
B. Conditions existing at time of inspection for bidding purpose will be maintained by Owner as
far as practical.
1. Before selective demolition, Owner will remove the following items:
a. Furnishings.
C. Notify Architect of discrepancies between existing conditions and Drawings before proceeding
with selective demolition.
CORNELL UNIVERSITY SECTION 02 41 19
Ithaca, New York SELECTIVE DEMOLITION
122 McGRAW PLACE - SELECTIVE DEMOLITION 02 41 19 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
D. Hazardous Materials: Owner will coordinate removal of hazardous materials prior to start of the
Work.
1. Asbestos: The Owner conducted a survey of the work area for review; report attached to
Section 01 35 39 “General Health & Safety.”
2. It is not expected that additional hazardous materials will be encountered in the Work.
a. If suspected hazardous materials are encountered, do not disturb; immediately
notify Architect and Owner. Hazardous materials will be removed by Owner under
a separate contract.
E. Storage or sale of removed items or materials on-site is not permitted.
F. Utility Service: Maintain existing utilities indicated to remain in service and protect them
against damage during selective demolition operations.
1. Maintain fire-protection facilities in service during selective demolition operations.
1.4 COORDINATION
A. Arrange selective demolition schedule so as not to interfere with Owner's operations.
PART 2 - PRODUCTS
2.1 PERFORMANCE REQUIREMENTS
A. Regulatory Requirements: Comply with governing EPA notification regulations before
beginning selective demolition. Comply with hauling and disposal regulations of authorities
having jurisdiction.
B. Standards: Comply with ASSE A10.6 and NFPA 241.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Verify that utilities have been disconnected and capped before starting selective demolition
operations.
B. Verify that hazardous materials have been remediated before proceeding with building
demolition operations.
C. Survey of Existing Conditions: Record existing conditions by use of preconstruction
photographs or video.
1. Comply with requirements specified in Section 01 32 33 "Photographic Documentation."
CORNELL UNIVERSITY SECTION 02 41 19
Ithaca, New York SELECTIVE DEMOLITION
122 McGRAW PLACE - SELECTIVE DEMOLITION 02 41 19 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
2. Inventory and record the condition of items to be removed and salvaged. Provide
photographs or video of conditions that might be misconstrued as damage caused by
salvage operations.
3.2 UTILITY SERVICES AND MECHANICAL/ELECTRICAL SYSTEMS
A. Existing Services/Systems to Remain: Maintain services/systems indicated to remain and
protect them against damage.
B. Existing Services/Systems to Be Removed, Relocated, or Abandoned: Locate, identify,
disconnect, and seal or cap off utility services and mechanical/electrical systems serving areas
to be selectively demolished.
1. Arrange to shut off utilities with Cornell.
2. If services/systems are required to be removed, relocated, or abandoned, provide
temporary services/systems that bypass area of selective demolition and that maintain
continuity of services/systems to other occupied parts of building.
3. Disconnect, demolish, and remove fire-suppression systems, plumbing, and HVAC
systems, equipment, and components indicated on Drawings to be removed.
a. Piping to Be Removed: Remove portion of piping indicated to be removed and cap
or plug remaining piping with same or compatible piping material.
b. Piping to Be Abandoned in Place: Drain piping and cap or plug piping with same
or compatible piping material and leave in place.
c. Equipment to Be Removed: Disconnect and cap services and remove equipment.
d. Equipment to Be Removed and Reinstalled: Disconnect and cap services and
remove, clean, and store equipment; when appropriate, reinstall, reconnect, and
make equipment operational.
e. Equipment to Be Removed and Salvaged: Disconnect and cap services and remove
equipment and deliver to Owner.
3.3 PROTECTION
A. Temporary Protection: Provide temporary barricades and other protection required to prevent
injury to people and damage to adjacent buildings and facilities to remain.
1. Provide protection to ensure safe passage of people around selective demolition area and
to and from occupied portions of building.
2. Comply with requirements for temporary enclosures, dust control, heating, and cooling
specified in Section 01 50 00 "Temporary Facilities and Controls."
B. Remove temporary barricades and protections where hazards no longer exist.
3.4 SELECTIVE DEMOLITION, GENERAL
A. General: Demolish and remove existing construction only to the extent required by new
construction and as indicated. Use methods required to complete the Work within limitations of
governing regulations and as follows:
CORNELL UNIVERSITY SECTION 02 41 19
Ithaca, New York SELECTIVE DEMOLITION
122 McGRAW PLACE - SELECTIVE DEMOLITION 02 41 19 - 4
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1. Neatly cut openings and holes plumb, square, and true to dimensions required. Use
cutting methods least likely to damage construction to remain or adjoining construction.
Use hand tools or small power tools designed for sawing or grinding, not hammering and
chopping. Temporarily cover openings to remain.
2. Cut or drill from the exposed or finished side into concealed surfaces to avoid marring
existing finished surfaces.
3. Do not use cutting torches until work area is cleared of flammable materials. At
concealed spaces, such as duct and pipe interiors, verify condition and contents of hidden
space before starting flame-cutting operations. Maintain portable fire-suppression devices
during flame-cutting operations.
4. Maintain adequate ventilation when using cutting torches.
5. Remove decayed, vermin-infested, or otherwise dangerous or unsuitable materials and
promptly dispose of off-site.
6. Locate selective demolition equipment and remove debris and materials so as not to
impose excessive loads on supporting walls, floors, or framing.
7. Dispose of demolished items and materials promptly.
B. Site Access and Temporary Controls: Conduct selective demolition and debris-removal
operations to ensure minimum interference with roads, streets, walks, walkways, and other
adjacent occupied and used facilities.
C. Salvaged (Removed) and Reinstalled Items:
1. Clean and repair items to functional condition adequate for intended reuse.
2. Pack or crate items after cleaning and repairing. Identify contents of containers.
3. Protect items from damage during transport and storage.
4. Reinstall items in locations indicated. Comply with installation requirements for new
materials and equipment. Provide connections, supports, and miscellaneous materials
necessary to make item functional for use indicated.
D. Existing Items to Remain: Protect construction indicated to remain against damage and soiling
during selective demolition. When permitted by Architect, items may be removed to a suitable,
protected storage location during selective demolition and cleaned and reinstalled in their
original locations after selective demolition operations are complete.
3.5 SELECTIVE DEMOLITION PROCEDURES FOR SPECIFIC MATERIALS
A. Masonry: Demolish in small sections. Cut masonry at junctures with construction to remain,
using power-driven saw, and then remove masonry between saw cuts.
B. Concrete Slabs-on-Grade: Saw-cut perimeter of area to be demolished, and then break up and
remove.
C. Resilient Floor Coverings: Remove floor coverings and adhesive according to recommendations
in RFCI's "Recommended Work Practices for the Removal of Resilient Floor Coverings." Do
not use methods requiring solvent-based adhesive strippers.
CORNELL UNIVERSITY SECTION 02 41 19
Ithaca, New York SELECTIVE DEMOLITION
122 McGRAW PLACE - SELECTIVE DEMOLITION 02 41 19 - 5
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
3.6 DISPOSAL OF DEMOLISHED MATERIALS
A. Remove demolition waste materials from Project site and recycle or dispose of them according
to Section 01 74 19 "Construction Waste Management and Disposal."
1. Do not allow demolished materials to accumulate on-site.
2. Remove and transport debris in a manner that will prevent spillage on adjacent surfaces
and areas.
B. Burning: Do not burn demolished materials.
3.7 CLEANING
A. Clean adjacent structures and improvements of dust, dirt, and debris caused by selective
demolition operations. Return adjacent areas to condition existing before selective demolition
operations began.
END OF SECTION 02 41 19
CORNELL UNIVERSITY SECTION 06 64 00
Ithaca, New York PLASTIC PANELING
122 McGRAW PLACE - PLASTIC PANELING 06 64 00 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 06 64 00 - PLASTIC PANELING
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of plastic paneling shown on the
Drawings or called for in the Project Manual including but not limited to:
1. Plastic sheet wall paneling – FRP (fiberglass reinforced plastic) paneling.
1.2 ACTION SUBMITTALS
A. Product Data: For each type of product.
B. Samples: For plastic paneling and trim accessories.
1.3 QUALITY ASSURANCE
A. Testing Agency: Acceptable to authorities having jurisdiction and FM Approvals.
B. Surface-Burning Characteristics: Determined by testing identical products according to ASTM
E 84 by a testing agency acceptable to authorities having jurisdiction.
1.4 WARRANTY
A. Special Warranty: Manufacturer agrees to repair or replace defective panels and components
that fail in materials or workmanship under normal conditions of use within specified warranty
period.
1. Failures, include, but are not limited to, the following:
a. Exposed fibers.
b. Rust.
c. Rot.
d. Corrosion.
e. Structural surface cracks.
f. Painting or refinishing required with normal pigmentation and UV degradation
excepted.
2. Warranty Period: Ten years from the date of Substantial Completion.
CORNELL UNIVERSITY SECTION 06 64 00
Ithaca, New York PLASTIC PANELING
122 McGRAW PLACE - PLASTIC PANELING 06 64 00 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
PART 2 - PRODUCTS
2.1 PLASTIC SHEET PANELING
A. Glass-Fiber-Reinforced Plastic Paneling: Gelcoat-finished, glass-fiber-reinforced plastic panels
complying with ASTM D 5319. Panels shall be USDA accepted for incidental food contact.
1. Basis of Design Product: Subject to compliance with requirements, provide Crane
Composites, Inc.; Sequentia Flat series or a comparable product by one of the following:
a. Glasteel/Marlite/Nudo Products.
b. Newcourt, Inc.
c. Parkland Plastics, Inc.
2. Surface-Burning Characteristics: As follows when tested by a qualified testing agency
according to ASTM E 84. Identify products with appropriate markings of applicable
testing agency.
a. Flame-Spread Index: 25 or less.
b. Smoke-Developed Index: 450 or less.
3. Nominal Thickness: Not less than 0.075 inch.
4. Wall Panel Size: 4 feet by 9 feet.
5. Surface Finish: Smooth.
6. Color: White.
2.2 ACCESSORIES
A. Trim Accessories: Manufacturer's standard one-piece vinyl extrusions designed to retain and
cover edges of panels. Provide division bars, inside corners, and caps as needed to conceal
edges.
1. Color: White.
B. Adhesive: As recommended by manufacturer for application indicated.
C. Sealant: Mildew-resistant, single-component, neutral-curing silicone sealant recommended by
plastic paneling manufacturer and complying with requirements in Section 07 92 00 "Joint
Sealants."
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates and conditions, with Installer present, for compliance with requirements for
installation tolerances and other conditions affecting performance of the Work.
CORNELL UNIVERSITY SECTION 06 64 00
Ithaca, New York PLASTIC PANELING
122 McGRAW PLACE - PLASTIC PANELING 06 64 00 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1. Corners: Plumb and straight.
2. Surfaces: Smooth, sound, and uniform.
a. Existing painted surfaces (gypsum drywall and plaster): Perforate with wallpaper
removal tool or minimum 20-grit sandpaper to provide rough surface to improve
adhesion.
3. Joints and cracks: Filled flush and smooth with adjoining surfaces.
4. Nails or screw fasteners: Countersunk.
B. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 PREPARATION
A. Acclimate panels to operating humidity conditions prior to layout and installation,
B. Clean substrates of substances that could impair adhesive bond, including oil, grease, dirt, and
dust.
C. Prepare substrates by sanding high spots and filling low spots as needed to provide a flat, even
surface for panel installation.
D. Ensure that all HVAC, plumbing, and electrical work above the ceiling level has been
completed.
E. Condition panels by unpacking and placing in installation space before installation according to
manufacturer's written recommendations.
F. Lay out paneling before installing. Locate panel joints where indicated on Drawings.
1. Mark plumb lines on substrate at panel joint locations for accurate installation.
2. Locate Panel joints to allow clearance at panel edges according to manufacturer’s written
instruction.
3.3 INSTALLATION
A. Install plastic paneling according to manufacturer's written instructions.
1. Do all cutting with carbide tipped saw blades or drill bits, or cut with snips.
2. Install panels plumb, level, square, flat, and in proper alignment.
3. Install panels to be water-resistant and washable.
4. Install panels with manufacturer’s recommended gap for panel field and corner joints.
B. Install panels in a full spread of adhesive.
C. Install trim accessories with adhesive and nails. Do not fasten through panels.
1. Allow for manufacturer’s recommending expansion spacing between panels, top and
bottom, and panel-to-panel.
CORNELL UNIVERSITY SECTION 06 64 00
Ithaca, New York PLASTIC PANELING
122 McGRAW PLACE - PLASTIC PANELING 06 64 00 - 4
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
D. Fill grooves in trim accessories with sealant before installing panels, and bed inside corner trim
in a bead of sealant.
E. Maintain uniform space between panels and wall fixtures. Fill space with sealant.
F. Remove excess sealant and smears as paneling is installed. Clean with solvent recommended by
sealant manufacturer and then wipe with clean dry cloths until no residue remains.
END OF SECTION 06 64 00
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 07 92 00 - JOINT SEALANTS
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of joint sealants shown on the
Drawings or called for in the Project Manual including but not limited to:
1. Nonstaining silicone joint sealants.
2. Urethane joint sealants.
3. Mildew-resistant joint sealants.
4. Latex joint sealants.
1.2 ACTION SUBMITTALS
A. Product Data: For each joint-sealant product.
B. Samples: For each kind and color of joint sealant required.
1.3 WARRANTY
A. Special Installer's Warranty: Installer agrees to repair or replace joint sealants that do not
comply with performance and other requirements specified in this Section within specified
warranty period.
1. Warranty Period: Two years from date of Substantial Completion.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Products: Subject to compliance with requirements, provide one of the following available
products that may be incorporated into the Work include, but are not limited to the following:
1. Dow Corning.
2. Sika Corporation.
3. Tremco Incorporated.
2.2 JOINT SEALANTS, GENERAL
A. Colors of Exposed Joint Sealants: As selected by Architect from manufacturer's full range.
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
2.3 NONSTAINING SILICONE JOINT SEALANTS
A. Silicone, Nonstaining, S, NS, 50, NT: Nonstaining, single-component, nonsag, plus 50 percent
and minus 50 percent movement capability, nontraffic-use, neutral-curing silicone joint sealant;
ASTM C 920, Type S, Grade NS, Class 50, Use NT.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Spectrem 2.
B. Silicone, Nonstaining, M, NS, 50, NT: Nonstaining, multi-component, nonsag, plus 50 percent
and minus 50 percent movement capability, nontraffic-use, neutral-curing silicone joint sealant;
ASTM C 920, Type S, Grade NS, Class 50, Use NT.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Spectrem 4.
C. Silicone, Nonstaining, S, NS, 25, T, NT: Nonstaining, single-component, nonsag, plus 25
percent movement capability, traffic- and nontraffic-use, neutral-curing silicone joint sealant;
ASTM C 920, Type S, Grade NS, Class 25, Uses T and NT.
1. Custom Building Products; 100% Silicone Sealant.
2. Laticrete; Latasil.
2.4 URETHANE JOINT SEALANTS
A. Urethane, M, P, 50, T, NT: Multicomponent, pourable, plus 50 percent and minus 50 percent
movement capability, traffic- and nontraffic-use, urethane joint sealant; ASTM C 920, Type M,
Grade P, Class 50, Uses T and NT.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Vulkem 445SSL.
B. Urethane, S, NS, 25, T, NT: Single-component, nonsag, plus 25 percent and minus 25 percent
movement capability, traffic- and nontraffic-use, urethane joint sealant; ASTM C 920, Type S,
Grade NS, Class 25, Uses T and NT.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Vulkem 45.
C. Urethane, S, P, 25, T, NT: Single-component, pourable, plus 25 percent and minus 25 percent
movement capability, traffic- and nontraffic-use, urethane joint sealant; ASTM C 920, Type S,
Grade P, Class 25, Uses T and NT.
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Dymonic.
2.5 MILDEW-RESISTANT JOINT SEALANTS
A. Mildew-Resistant Joint Sealants: Formulated for prolonged exposure to humidity with fungicide
to prevent mold and mildew growth.
B. Silicone, Mildew Resistant, Acid Curing, S, NS, 25, NT: Mildew-resistant, single-component,
nonsag, plus 25 percent and minus 25 percent movement capability, nontraffic-use, acid-curing
silicone joint sealant; ASTM C 920, Type S, Grade NS, Class 25, Use NT.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Tremsil 200.
C. Acrylic Latex: Acrylic latex or siliconized acrylic latex, ASTM C 834, Type OP, Grade NF.
1. Basis of Design: Subject to compliance with requirements, provide the following or
comparable product approved by Architect:
a. Tremco Incorporated; Tremflex 834.
2.6 JOINT-SEALANT BACKING
A. Cylindrical Sealant Backings: ASTM C 1330, Type C (closed-cell material with a surface skin),
Type O (open-cell material), Type B (bicellular material with a surface skin) or any of the
preceding types, as approved in writing by joint-sealant manufacturer for joint application
indicated, and of size and density to control sealant depth and otherwise contribute to producing
optimum sealant performance.
B. Bond-Breaker Tape: Polyethylene tape or other plastic tape recommended by sealant
manufacturer.
2.7 MISCELLANEOUS MATERIALS
A. Primer: Material recommended by joint-sealant manufacturer where required for adhesion of
sealant to joint substrates indicated, as determined from preconstruction joint-sealant-substrate
tests and field tests.
B. Cleaners for Nonporous Surfaces: Chemical cleaners acceptable to manufacturers of sealants
and sealant backing materials.
C. Masking Tape: Nonstaining, nonabsorbent material compatible with joint sealants and surfaces
adjacent to joints.
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 4
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
PART 3 - EXECUTION
3.1 PREPARATION
A. Surface Cleaning of Joints: Clean out joints immediately before installing joint sealants to
comply with joint-sealant manufacturer's written instructions and the following requirements:
1. Clean nonporous joint substrate surfaces with chemical cleaners or other means that do
not stain, harm substrates, or leave residues capable of interfering with adhesion.
B. Joint Priming: Prime joint substrates where recommended by joint-sealant manufacturer or as
indicated by preconstruction joint-sealant-substrate tests or prior experience.
C. Masking Tape: Use masking tape where required to prevent contact of sealant or primer with
adjoining surfaces.
3.2 INSTALLATION OF JOINT SEALANTS
A. General: Comply with ASTM C 1193 and joint-sealant manufacturer's written installation
instructions for products and applications indicated, unless more stringent requirements apply.
B. Install sealant backings of kind indicated to support sealants during application and at position
required to produce cross-sectional shapes and depths of installed sealants relative to joint
widths that allow optimum sealant movement capability.
C. Install bond-breaker tape behind sealants where sealant backings are not used between sealants
and backs of joints.
D. Install sealants using proven techniques that comply with the following and at the same time
backings are installed:
1. Place sealants so they directly contact and fully wet joint substrates.
2. Completely fill recesses in each joint configuration.
3. Produce uniform, cross-sectional shapes and depths relative to joint widths that allow
optimum sealant movement capability.
E. Tooling of Nonsag Sealants: Immediately after sealant application and before skinning or curing
begins, tool sealants to form smooth, uniform beads of configuration indicated. Use tooling
agents that are approved in writing by sealant manufacturer and that do not discolor sealants or
adjacent surfaces.
1. Provide concave joint profile per Figure 8A in ASTM C 1193 unless otherwise indicated.
3.3 JOINT-SEALANT SCHEDULE
A. Joint-Sealant Application: Exterior joints in vertical surfaces and horizontal nontraffic surfaces.
1. Joint Locations:
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 5
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
a. Construction joints in cast-in-place concrete.
b. Joints in stone masonry.
c. Control and expansion joints in unit masonry.
d. Joints in sheet metal fabrications.
e. Other joints as indicated on Drawings.
2. Joint Sealant: Silicone, mildew resistant, acid curing, S, NS, 25, NT.
3. Joint Sealant: Silicone, nonstaining, S, NS, 50, NT.
4. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors.
B. Joint-Sealant Application: Interior joints in vertical surfaces and horizontal nontraffic surfaces.
1. Joint Locations:
a. Control and expansion joints on exposed interior surfaces of exterior walls.
b. Vertical joints on exposed surfaces of unit masonry and concrete walls.
c. Other joints as indicated on Drawings.
2. Joint Sealant: Silicone, nonstaining, M, NS, 50, NT.
3. Joint Sealant: Urethane, S, NS, 25, NT.
4. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors.
C. Joint-Sealant Application: Interior joints in horizontal traffic surfaces.
1. Joint Locations:
a. Isolation joints in cast-in-place concrete slabs.
b. Control and expansion joints in stone flooring.
c. Control and expansion joints in tile flooring.
d. Other joints as indicated on Drawings.
2. Joint Sealant: Silicone, nonstaining, S, NS, 25, T, NT.
3. Joint-Sealant Color: Color: As selected by Architect from manufacturer's full range of
colors.
D. Joint-Sealant Application: Specific interior joints in vertical surfaces and horizontal nontraffic
surfaces.
1. Joint Locations:
a. Joint between PVC piping and concrete slab.
2. Joint Sealant: Urethane, S, NS, 25, NT.
3. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors.
E. Joint-Sealant Application: Interior joints in vertical surfaces and horizontal nontraffic surfaces
not subject to significant movement.
1. Joint Locations:
a. Control joints on exposed interior surfaces of exterior walls.
CORNELL UNIVERSITY SECTION 07 92 00
Ithaca, New York JOINT SEALANTS
122 McGRAW PLACE - JOINT SEALANTS 07 92 00 - 6
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
b. Perimeter joints between interior wall surfaces and frames of interior doors and
windows.
c. Other joints as indicated on Drawings.
2. Joint Sealant: Acrylic latex.
3. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors.
F. Joint-Sealant Application: Mildew-resistant interior joints in vertical surfaces and horizontal
nontraffic surfaces.
1. Joint Locations:
a. Tile control and expansion joints where indicated.
b. Other joints as indicated on Drawings.
2. Joint Sealant: Silicone, mildew resistant, acid curing, S, NS, 25, NT.
3. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors.
END OF SECTION 07 92 00
CORNELL UNIVERSITY SECTION 09 30 13
Ithaca, New York CERAMIC TILING
122 McGRAW PLACE - CERAMIC TILING 09 30 13 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 09 30 13 - CERAMIC TILING
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of ceramic tiling shown on the
Drawings or called for in the Project Manual including but not limited to:
1. Quarry tile.
B. Related Requirements:
1. Section 07 92 00 “Joint Sealants” for joint sealants in tiling applications.
1.2 ACTION SUBMITTALS
A. Product Data: For each type of product. Product Data: For each type of product.
1. Include preparation instructions and recommendations.
2. Include written manufacturer’s instructions for installation.
B. Preliminary Selection Samples: Color charts indicating manufacturer’s full range of color
selections.
1.3 QUALITY ASSURANCE
A. Installer Qualifications:
1. Installer is a five-star member of the National Tile Contractors Association or is approved
by Cornell University Project Manager.
1.4 PERFORMANCE REQUIREMENTS
A. Products shall comply with the following:
1. Static of Coefficient of Friction: Tile on walkway surfaces shall be provided with the
following values as tested in accordance with ASTM C 1028:
a. Level Surfaces: Minimum of 0.6 (wet).
CORNELL UNIVERSITY SECTION 09 30 13
Ithaca, New York CERAMIC TILING
122 McGRAW PLACE - CERAMIC TILING 09 30 13 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1.5 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials that match and are from same production runs as products installed and
that are packaged with protective covering for storage and identified with labels describing
contents.
1. Tile and Trim Units: Furnish quantity of full-size units equal to 3 percent of amount
installed for each type, composition, color, pattern, and size indicated.
PART 2 - PRODUCTS
2.1 PRODUCTS, GENERAL
A. ANSI Ceramic Tile Standard: Provide Standard-grade tile that complies with ANSI A137.1 for
types, compositions, and other characteristics indicated.
B. ANSI Standards for Tile Installation Materials: Provide materials complying with
ANSI A108.02, ANSI standards referenced in other Part 2 articles, ANSI standards referenced
by TCNA installation methods specified in tile installation schedules, and other requirements
specified.
2.2 TILE PRODUCTS
A. Ceramic Tile Type CT-1: Unglazed square-edged quarry tile.
1. Basis of Design: Subject to compliance with requirements provide Daltile; Quarry Tile
series or approved equal.
2. Size: 6 by 6 inches.
3. Thickness: 1/2 inch.
4. Wearing Surface: Nonabrasive, smooth.
5. Dynamic Coefficient of Friction: Not less than 0.42.
6. Tile Color: Red Blaze (0Q40). Verify to match existing.
7. Grout Color: Match existing and as selected by Architect from manufacturer's full range.
2.3 SETTING MATERIALS
A. Portland Cement Mortar (Thickset) Installation Materials: ANSI A108.02.
1. Portland Cement: ASTM C150, Type 1, gray.
2. Hydrated Lime: ASTM C207, Type S.
3. Sand: ASTM C144, Fine.
4. Water: Potable.
B. Improved Modified Dry-Set Mortar (Thinset): ANSI A118.15.
1. Products: Subject to compliance with requirements, provide one of the following:
CORNELL UNIVERSITY SECTION 09 30 13
Ithaca, New York CERAMIC TILING
122 McGRAW PLACE - CERAMIC TILING 09 30 13 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
a. ARDEX Americas.
b. Bonsal American, an Oldcastle company.
c. C-Cure.
d. Custom Building Products.
e. LATICRETE SUPERCAP, LLC.
f. MAPEI Corporation.
2. Provide prepackaged, dry-mortar mix to which only water must be added at Project site.
3. Provide prepackaged, dry-mortar mix combined with liquid-latex additive at Project site.
4. For wall applications, provide nonsagging mortar.
2.4 GROUT MATERIALS
A. High-Performance Tile Grout: ANSI A118.7.
1. Products: Subject to compliance with requirements, provide one of the following:
a. ARDEX Americas.
b. Boiardi Products Corporation; a QEP company.
c. Bonsal American, an Oldcastle company.
d. Bostik, Inc.
e. C-Cure.
f. Custom Building Products.
g. Jamo Inc.
h. LATICRETE SUPERCAP, LLC.
i. MAPEI Corporation.
j. Summitville Tiles, Inc.
2. Polymer Type: Dry, redispersible form, prepackaged with other dry ingredients.
3. Polymer Type: Liquid-latex form for addition to prepackaged dry-grout mix.
2.5 MISCELLANEOUS MATERIALS
A. Trowelable Underlayments and Patching Compounds: Latex-modified, portland cement-based
formulation provided or approved by manufacturer of tile-setting materials for installations
indicated.
B. Floor Sealer: Manufacturer's standard product for sealing grout joints and that does not change
color or appearance of grout.
1. Products: Subject to compliance with requirements, provide one of the following:
a. Bonsal American, an Oldcastle company.
b. Custom Building Products.
c. Jamo Inc.
d. Summitville Tiles, Inc.
C. Silicone Sealant: Silicone sealant, non-staining type, approved for use in traffic conditions.
Refer to Section 07 92 00 “Joint Sealants.”
CORNELL UNIVERSITY SECTION 09 30 13
Ithaca, New York CERAMIC TILING
122 McGRAW PLACE - CERAMIC TILING 09 30 13 - 4
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates, areas, and conditions where tile will be installed, with Installer present, for
compliance with requirements for installation tolerances and other conditions affecting
performance of the Work.
1. Verify that substrates for setting tile are firm; dry; clean; free of coatings that are
incompatible with tile-setting materials, including curing compounds and other
substances that contain soap, wax, oil, or silicone; and comply with flatness tolerances
required by ANSI A108.01 for installations indicated.
2. Verify that concrete substrates for tile floors installed with thinset mortar comply with
surface finish requirements in ANSI A108.01 for installations indicated.
3. Verify that substrates are level within installation tolerances required for specific
application.
B. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 PREPARATION
A. Fill cracks, holes, and depressions in concrete substrates for tile floors installed with thinset
mortar with trowelable leveling and patching compound specifically recommended by tile-
setting material manufacturer.
B. Blending: For tile exhibiting color variations, verify that tile has been factory blended and
packaged so tile units taken from one package show same range of colors as those taken from
other packages and match approved Samples. If not factory blended, either return to
manufacturer or blend tiles at Project site before installing.
3.3 CERAMIC TILE INSTALLATION
A. Comply with TCNA's "Handbook for Ceramic, Glass, and Stone Tile Installation" for TCNA
installation methods specified in tile installation schedules. Comply with parts of the
ANSI A108 series "Specifications for Installation of Ceramic Tile" that are referenced in TCNA
installation methods, specified in tile installation schedules, and apply to types of setting and
grouting materials used.
1. For the following installations, follow procedures in the ANSI A108 series of tile
installation standards for providing 95 percent mortar coverage:
a. Tile floors consisting of tiles 8 by 8 inches or larger.
b. Tile floors consisting of rib-backed tiles.
B. Extend tile work into recesses and under or behind equipment and fixtures to form complete
covering without interruptions unless otherwise indicated. Terminate work neatly at
obstructions, edges, and corners without disrupting pattern or joint alignments.
CORNELL UNIVERSITY SECTION 09 30 13
Ithaca, New York CERAMIC TILING
122 McGRAW PLACE - CERAMIC TILING 09 30 13 - 5
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
C. Accurately form intersections and returns. Perform cutting and drilling of tile without marring
visible surfaces. Carefully grind cut edges of tile abutting trim, finish, or built-in items for
straight aligned joints. Fit tile closely to electrical outlets, piping, fixtures, and other
penetrations so plates, collars, or covers overlap tile.
D. Jointing Pattern: Lay tile in grid pattern to match existing. Lay out tile work to minimize the use
of pieces that are less than half of a tile. Provide uniform joint widths unless otherwise
indicated.
E. Joint Widths: Unless otherwise indicated, install tile with the following joint widths:
1. Quarry Tile: 3/8 inch, Verify to match existing.
F. Expansion Joints: Provide expansion joints and other sealant-filled joints, including control,
contraction, and isolation joints, where indicated. Form joints during installation of setting
materials, mortar beds, and tile. Do not saw-cut joints after installing tiles.
G. Floor Sealer: Apply floor sealer to cementitious grout joints in tile floors according to floor-
sealer manufacturer's written instructions. As soon as floor sealer has penetrated grout joints,
remove excess sealer and sealer from tile faces by wiping with soft cloth.
3.4 INTERIOR CERAMIC TILE INSTALLATION SCHEDULE
A. Interior Floor Installations, Concrete Subfloor:
1. Ceramic Tile Installation: TCNA F113 (similar); thinset mortar on a medium bed mortar
thickness.
a. Ceramic Tile Type: CT-1, CT-2, and CT-3.
b. Thinset Mortar: Improved modified dry-set mortar on medium bed mortar (1/2” or
greater).
c. Grout: High-performance sanded grout.
END OF SECTION 09 30 13
CORNELL UNIVERSITY SECTION 09 51 13
Ithaca, New York ACOUSTICAL PANEL CEILINGS
122 McGRAW PLACE - ACOUSTICAL PANEL CEILINGS 09 51 13 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 09 51 13 - ACOUSTICAL PANEL CEILINGS
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of acoustical panel ceilings shown
on the Drawings or called for in the Project Manual including but not limited to:
1. Acoustical panels and exposed suspension systems for interior ceilings.
a. Dish Room: Acoustical panels.
1.2 ACTION SUBMITTALS
A. Product Data: For each type of product.
B. Samples: For each exposed product and for each color and texture specified.
1.3 CLOSEOUT SUBMITTALS
A. Maintenance data.
1.4 WARRANTY
A. Acoustical ceiling panels: Provide manufacturer’s 30-year performance limited warranty against
visible sag, mold, and mildew.
B. Metal suspension system: Provide manufacturer’s 10 year limited warranty and 30 year limited
warranty with HumiGuard Plus products.
1.5 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials, from the same product run, that match products installed and that are
packaged with protective covering for storage and identified with labels describing contents.
1. Acoustical Ceiling Units: Four (4) full-size panels percent of quantity installed.
CORNELL UNIVERSITY SECTION 09 51 13
Ithaca, New York ACOUSTICAL PANEL CEILINGS
122 McGRAW PLACE - ACOUSTICAL PANEL CEILINGS 09 51 13 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
PART 2 - PRODUCTS
2.1 PERFORMANCE REQUIREMENTS
A. Surface-Burning Characteristics: Comply with ASTM E 84; testing by a qualified testing
agency. Identify products with appropriate markings of applicable testing agency.
1. Flame-Spread Index: Class A according to ASTM E 1264.
2. Smoke-Developed Index: 50 or less.
2.2 ACOUSTICAL PANELS
A. Acoustical Panels: Provide square lay-in, smooth texture, water-repellent, washable, scratch-
and-soil-resistant panels.
1. Basis of Design: Subject to compliance with requirements, provide Armstrong Ceilings;
Kitchen Zone or comparable equal.
B. Acoustical Panel Standard: Manufacturer's standard panels according to ASTM E 1264.
C. Classification: Type IX, Form 2, Pattern G, Fire Class A.
D. Color: White.
E. Light Reflectance (LR): 0.89.
F. Ceiling Attenuation Class (CAC): 33.
G. Edge/Joint Detail: Square.
H. Thickness: 15/16-inch.
I. Modular Size: 24 by 48 inches.
2.3 METAL SUSPENSION SYSTEM
A. Metal suspension system: Provide aluminum construction system.
1. Basis of Design: Subject to compliance with requirements, provide Armstrong Ceilings;
15/16” Clean Room Co-Extruded Aluminum or comparable equal.
B. Metal Suspension-System Standard: Manufacturer's standard, direct-hung, metal suspension
system and accessories according to ASTM C 635/C 635M.
C. Wide-Face, Capped, Double-Web, Steel Suspension System: Main and cross runners of co-
extruded aluminum; with prefinished 15/16-inch- wide metal caps on flanges.
1. Structural Classification: Heavy-duty system.
CORNELL UNIVERSITY SECTION 09 51 13
Ithaca, New York ACOUSTICAL PANEL CEILINGS
122 McGRAW PLACE - ACOUSTICAL PANEL CEILINGS 09 51 13 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
2. Face Design: Flat, flush.
3. Cap Material: Aluminum.
4. Cap Finish: Painted white.
2.4 ACCESSORIES
A. Attachment Devices: Size for five times the design load indicated in ASTM C 635/C 635M,
Table 1, "Direct Hung," unless otherwise indicated. Comply with seismic design requirements.
B. Hold-Down Clips: Manufacturer's standard hold-down.
2.5 METAL EDGE MOLDINGS AND TRIM
A. Roll-Formed, Sheet-Metal Edge Moldings and Trim: Type and profile indicated or, if not
indicated, manufacturer's standard moldings for edges and penetrations that comply with
seismic design requirements; formed from sheet metal of same material, finish, and color as that
used for exposed flanges of suspension-system runners.
PART 3 - EXECUTION
3.1 PREPARATION
A. Measure each ceiling area and establish layout of acoustical panels to balance border widths at
opposite edges of each ceiling. Avoid using less-than-half-width panels at borders unless
otherwise indicated.
B. Layout openings for penetrations centered on the penetrating items.
3.2 INSTALLATION
A. Install acoustical panel ceilings according to ASTM C 636/C 636M and manufacturer's written
instructions.
B. Install edge moldings and trim of type indicated at perimeter of acoustical ceiling area and
where necessary to conceal edges of acoustical panels.
1. Apply acoustical sealant in a continuous ribbon concealed on back of vertical legs of
moldings before they are installed.
2. Do not use exposed fasteners, including pop rivets, on moldings and trim.
3. Arrange directionally patterned acoustical panels as indicated on Drawings.
END OF SECTION 09 51 13
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 1
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 09 91 00 - PAINTING
PART 1 - GENERAL
1.1 SUMMARY
A. The work to be done under this section includes all equipment, labor, materials, and accessories
required for the furnishing, setting in place, and completion of exterior and interior painting
shown on the Drawings or called for in the Project Manual including but not limited to surface
preparation and the application of paint systems on the following exterior and interior
substrates:
1. Steel and iron.
2. Galvanized metal.
3. Wood.
4. Gypsum board.
5. Plaster.
6. Plastic/PVC piping.
1.2 DEFINITIONS
A. MPI Gloss Level 4: 20 to 35 units at 60 degrees and not less than 35 units at 85 degrees,
according to ASTM D 523.
B. MPI Gloss Level 5: 35 to 70 units at 60 degrees, according to ASTM D 523.
C. MPI Gloss Level 6: 70 to 85 units at 60 degrees, according to ASTM D 523.
1.3 ACTION SUBMITTALS
A. Product Data: For each type of product. Include preparation requirements and application
instructions.
1. Primer.
2. Paint.
B. Selection Samples: For each type of paint system and each color and gloss of topcoat submit a
complete set of color chips that represent actual product, color, and sheen.
1. Interior Paints.
2. Exterior Paint.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 2
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
C. Mockup to test for paint adhesion on plastic PVC:
1. Provide a mockup of preparation and painting of a 24-inch section of PVC piping
specified for radon mitigation system.
a. Following proper drying times, submit mockup to Owner and Architect for review.
b. Mockup review for primarily to understand specified systems adhesion to plastic.
1.4 DELIVERY, STORAGE AND HANDLING
A. Deliver manufacturer’s unopened containers to work site. Packaging shall bear the
manufacturer’s name, label and the following information:
1. Product name and type (description).
2. Application and use instructions.
3. Surface preparation instructions.
4. VOC content.
5. Batch date.
6. Color number.
B. Store materials not in use in tightly covered containers in a well-ventilated area that is within
acceptable temperature range, per manufacturer’s written instructions. Maintain storage
containers in a clean condition, free of foreign materials and residue.
C. Store and dispose of solvent-based materials, and materials used with solvent-based materials,
in accordance with requirements of authorities having jurisdiction.
1.5 PROJECT CONDITIONS
A. Apply waterborne paints only when temperatures of surfaces to be painted and surrounding air
are between 50 and 90 deg F. Apply solvent-thinned paints only when temperatures of surfaces
to be painted and surrounding air are between 45 and 95 deg F.
B. All exposed bare wood shall be primed within one week of exposure or installation. If
temperature does not permit priming, apply paintable wood preservative within one week of
exposure or installation. Preservative may be sprayed or brushed.
C. Do not paint in snow, rain, fog, or mist; or when relative humidity exceeds 85 percent; or at
temperatures less than 5 deg F above the dew point; or to damp or wet surfaces.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Basis of Design: Subject to compliance with requirements, provide paint products approved by
Cornell University.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 3
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1. Approved Manufacturer: Benjamin Moore & Co.
2. SUBSTITUTIONS ARE NOT ALLOWED without prior approval by Owner.
2.2 PAINT, GENERAL
A. MPI Standards: Products shall comply with MPI standards indicated and shall be listed in its
"MPI Approved Products Lists."
B. Material Compatibility:
1. Materials for use within each paint system shall be compatible with one another and
substrates indicated, under conditions of service and application as demonstrated by
manufacturer, based on testing and field experience.
2. For each coat in a paint system, products shall be recommended in writing by topcoat
manufacturers for use in paint system and on substrate indicated.
C. Colors: As selected by Architect from manufacturer's full range.
1. Twenty percent of surface area will be painted with deep tones.
2.3 METAL PRIMERS
A. Primer, Alkyd, Anti-Corrosive for Metal: MPI #79.
B. Primer, Galvanized Cementitious, MPI #26.
2.4 EXTERIOR PRIMERS
A. Primer, Alkyd for Exterior Wood: MPI #5.
B. Primer, Modified Alkyd for Plastics.
1. Rust-Oleum; Specialty Plastic Primer Spray.
2.5 EXTERIOR SOLVENT-BASED PAINTS
A. Alkyd, Exterior, Semi-Gloss (Gloss Level 5): MPI #94.
B. Modified Alkyd for Plastics.
1. Rust-Oleum; Specialty Paint for Plastic.
2.6 INTERIOR PRIMERS
A. Primer, Latex, Water Based:
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 4
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
1. Benjamin Moore & Co.; Fresh Start High-Hiding All Purpose Primer (046).
2.7 INTERIOR WATER-BASED PAINTS
A. Latex, Interior, Flat, (Gloss Level 1):
1. Benjamin Moore & Co.; Waterborne Ceiling Paint (508).
B. Latex, Interior, Institutional Low Odor/VOC, (Gloss Level 4).
1. Benjamin Moore & Co.; Super Spec Interior Latex (Eggshell) (C274).
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates and conditions, with Applicator present, for compliance with requirements
for maximum moisture content and other conditions affecting performance of the Work.
B. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter
as follows:
1. Masonry (Clay and CMUs): 12 percent.
2. Wood: 15 percent.
3. Gypsum Board: 12 percent.
4. Plaster: 12 percent.
C. Verify suitability of substrates, including surface conditions and compatibility with existing
finishes and primers.
D. Comply with procedures specified in PDCA P4 for inspection and acceptance of surfaces to be
painted.
E. Proceed with coating application only after unsatisfactory conditions have been corrected.
1. Application of coating indicates acceptance of surfaces and conditions.
3.2 PREPARATION
A. Comply with manufacturer's written instructions and recommendations in "MPI Manual"
applicable to substrates and paint systems indicated.
B. Surface Preparation: Clean and prepare surfaces to be painted according to manufacturer’s
written instructions for each particular substrate condition and as specified.
1. Provide barrier coats over incompatible primers or remove and re-prime.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 5
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
2. New Wood: Clean surfaces of dirt, oil, and other foreign substances with scrapers,
mineral spirits, and sandpaper, as required. Sand surfaces exposed to view smooth and
dust off.
a. Scrape and clean small, dry, seasoned knots, and apply a thin coat of white shellac
or other recommended knot sealer before applying primer. After priming, fill
holes and imperfections in finish surfaces with putty or plastic wood filler. Sand
smooth when dried.
b. Prime wood to be painted immediately on delivery. Prime edges, ends, faces,
undersides, back sides, and cut edges of wood.
c. Condition replacement wood members to prevailing conditions at installation areas
before installing.
3. Existing Wood: Appropriate paint preparation includes stripping wood surfaces with
paint remover; applicator shall follow manufacturer’s written instructions for substrate.
a. Rotary sanders, pressurized water or aggregate blasting, or propriety machines that
remove excessive amounts of wood and leave swirls or gouges will not be used.
b. For stripping procedure, perform a test patch as per manufacturer’s instructions.
c. Protect adjacent building construction and landscaping from stripping operations.
d. Prepare substrate and strip existing wood as per written instructions.
e. All loose boards and missing or loose nails will be repaired or replaced prior to
priming. Replacement nails shall be stainless steel or hot-dipped galvanized steel.
f. Weathered gray (punky) or deteriorated wood shall be sanded to a bright, sound
substrate prior to priming. This can be accomplished with hand sanding, pad
(finish) sanders, or random orbit sanders.
g. Where sanding is not possible, weathered gray or deteriorated wood shall be
treated with a mixture of one-part boiled linseed oil and one-part mineral spirits as
a consolidant for the wood surface. Treatment shall dry prior to priming.
h. Feather edges of sanding as required for smooth transitions.
i. Caulking and filling procedures shall be completed after priming and not over bare
wood.
4. Ferrous Metals: Clean ungalvanized ferrous-metal surfaces; remove oil, grease, dirt,
loose mill scale, and other foreign substances.
a. Corrosion removal:
1) For corrosion pitting larger than 1/4-inch in diameter/1/8-inch depth,
abrasive clean with sandpaper to white metal appearance; prime. Patch with
epoxy resin cement.
2) For smaller corrosion pitting, clean and prime.
b. Remove only as much paint and rust each day as can be primed that same day –
within 2 hours.
c. Provide joint sealant at all areas affected by cleaning and paint removal processes,
especially seams, screw and bolt holes, and at junctures with other materials.
5. Plastic PVC piping:
a. Follow manufacturer’s written instructions for preparation and finishing.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 6
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
b. Apply 220-grit sandpaper to PVC surfaces to assist with adhesion to glossy
surface.
c. Clean with paint thinner. Proceed with manufacturer’s written instructions.
3.3 PREPARATION
A. Material Preparation:
1. Maintain containers used in mixing and applying paint in a clean condition, free of
foreign materials and residue.
2. Stir material before application to produce a mixture of uniform density. Stir as required
during application. Do not stir surface film into material. If necessary, remove surface
film and strain material before using.
3.4 APPLICATION
A. Scheduled Painting: Apply first coat to surfaces that have been cleaned, pretreated, or otherwise
prepared for painting as soon as practical after preparation and before subsequent surface
deterioration.
B. Application Procedures: Apply paints and coatings by brush, roller, spray, or other applicators
according to manufacturer’s written instructions. All spray work must be back-brushed or
rolled, and all unpainted surfaces protected from overspray.
C. Minimum Coating Thickness: Apply paint materials no thinner than manufacturer’s
recommended spreading rate. Provide total dry film thickness of the entire system as
recommended by manufacturer.
D. Prime Coats: Before applying finish coats, apply a prime coat, as recommended by
manufacturer, to material that is required to be painted or finished and that has not been prime
coated by others. Re-coat primed and sealed surfaces where evidence of suction spots or
unsealed areas in first coat appears, to ensure a finish coat with no burn-through or other defects
due to insufficient sealing.
E. Pigmented (Opaque) Finishes: Completely cover surfaces as necessary to provide a smooth,
opaque surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting,
holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections will not be
acceptable.
3.5 CLEANING AND PROTECTION
A. Protect work of other trades against damage from paint application. Correct damage to work of
other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and
leave in an undamaged condition.
B. At the end of each workday, remove empty cans, rags, rubbish, and other discarded paint
materials from Project site.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 7
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
3.6 PAINTING SCHEDULE
A. Exterior Wood Substrates: Existing exterior wood brick mold and casings.
1. Alkyd System:
a. SPOT PRIMING OR NEW: Prime Coat: Primer, alkyd for exterior wood, MPI #5.
b. Topcoat: Alkyd, exterior, semi-gloss (MPI Gloss Level 5), MPI #94.
B. Exterior Metal Substrates: Existing hollow metal door frame and casing members, and exterior
steel lintels.
1. Alkyd System:
a. SPOT PRIMING OR NEW: Prime Coat: Alkyd, Anti-Corrosive for Metal.
b. Intermediate Coat: Exterior, alkyd enamel, matching topcoat.
c. Topcoat: Alkyd, exterior, semi-gloss (MPI Gloss Level 5), MPI #94.
C. Exterior Plastic Substrates: New PVC piping – interior and exterior.
1. Modified Alkyd System:
a. Prime Coat: Modified Alkyd, Specialty Plastic Primer.
b. Intermediate Coat: Matching topcoat.
c. Topcoat: Modified Alkyd, Specialty Paint for Plastic.
d. Refer to Part 1.3 for MOCKUP requirements.
D. Interior Wood Substrates: Existing and new wood casings.
1. Institutional Low-Odor/VOC Latex System:
a. Prime Coat: Primer, Latex, Water-based; Fresh Start High-Hiding All Purpose
Primer.
1) Not required on existing painted surfaces.
b. Intermediate Coat: Latex, interior, institutional low odor/VOC, matching topcoat.
c. Topcoat: Latex, interior, institutional low odor/VOC, Super Spec Interior Latex
(Eggshell).
E. Interior Gypsum Board and Plaster Substrates; Existing and new gypsum board and plaster
surfaces:
1. Institutional Low-Odor/VOC Latex System:
a. Prime Coat: Primer sealer, Latex, Water-based, Fresh Start High-Hiding All
Purpose Primer.
1) Not required for existing substrates.
b. Intermediate Coat: Latex, interior, institutional low odor/VOC, matching topcoat.
CORNELL UNIVERSITY SECTION 09 90 00
Ithaca, New York PAINTING
122 McGRAW PLACE - PAINTING 09 91 00 - 8
BASEMENT RENOVATIONS Bero Architecture PLLC JUNE 11, 2018
RADON AND KITCHEN WORK
c. Topcoat: Latex, interior, institutional low odor/VOC, Super Spec Interior Latex
(Eggshell).
F. Interior Ceilings, Gypsum Board and Plaster Substrates - New and existing gypsum board and
plaster, and existing acoustical ceiling tiles:
1. Institutional Low-Odor/VOC Latex System:
a. Prime Coat: Primer, Latex, Water-based; Fresh Start High-Hiding All Purpose
Primer.
1) Not required for existing substrates.
b. Intermediate Coat: Latex, flat, matching topcoat.
c. Topcoat: Latex, interior, flat, Waterborne Ceiling Paint (Flat).
END OF SECTION 09 91 00
CORNELL UNIVERSITY SECTION 210580
Ithaca, New York FIRESTOPPING
122 McGRAW PLACE FIRESTOPPING 210580 - 1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 210580 - FIRESTOPPING
PART 1 - GENERAL
1.01 SUMMARY
A. Provide listed firestop at penetrations of rated walls, partitions, ceilings, floors and
assemblies.
1.02 DEFINITIONS
A. Firestopping: Material or combination of materials used to retain integrity of fire-rated
construction by maintaining an effective barrier against the spread of flame, smoke, and hot
gases through penetrations in fire rated wall and floor assemblies.
1.03 REFERENCES
A. Test Requirements: ASTM E 814, "Standard Method of Fire Tests of Through Penetration
Fire Stops"
B. Test Requirements: UL 1479, “Fire Tests of Through-Penetration Firestops”
C. Underwriters Laboratories (UL) of Northbrook, IL publishes tested systems in their "FIRE
RESISTANCE DIRECTORY" that is updated annually.
1. UL Fire Resistance Directory:
a. Firestop Devices (XHJI)
b. Fire Resistance Ratings (BXRH)
c. Through-Penetration Firestop Systems (XHEZ)
d. Fill, Voids, or Cavity Material (XHHW)
e. Forming Materials (XHKU)
D. International Firestop Council Guidelines for Evaluating Firestop Systems Engineering
Judgments
E. Inspection Requirements: ASTM E 2174, “Standard Practice for On-site Inspection of
Installed Fire Stops.”
F. ASTM E 84, “Standard Test Method for Surface Burning Characteristics of Building
Materials.”
1.04 QUALITY ASSURANCE
A. A manufacturer's direct representative to be on-site during initial installation of firestop
systems to train appropriate contractor personnel in proper selection and installation
procedures. This will be done per manufacturer's written recommendations published in
their literature and drawing details.
CORNELL UNIVERSITY SECTION 210580
Ithaca, New York FIRESTOPPING
122 McGRAW PLACE FIRESTOPPING 210580 - 2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
B. Firestop System installation must meet requirements of ASTM E 814 or UL 1479 tested
assemblies that provide a fire rating equal to that of construction being penetrated.
C. Proposed firestop materials and methods shall conform to applicable governing codes
having local jurisdiction.
1.05 SUBMITTALS
A. Submit Product Data: Manufacturer’s specifications and technical data for each material
including the composition and limitations, documentation of UL firestop systems to be used
and manufacturer's installation instructions.
B. Submit material safety data sheets provided with product delivered to job-site.
PART 2 - PRODUCTS
2.01 FIRESTOPPING, GENERAL
A. Provide firestopping composed of components that are compatible with each other, the
substrates forming openings, and the items, if any, penetrating the firestopping under
conditions of service and application, as demonstrated by the firestopping manufacturer
based on testing and field experience.
B. Provide components for each firestopping system that are needed to install fill material.
Use only components specified by the firestopping manufacturer and approved by the
qualified testing agency for the designated fire-resistance-rated systems.
2.02 ACCEPTABLE MANUFACTURERS
A. Subject to compliance with through penetration firestop systems (XHEZ) listed in Volume
II of the UL Fire Resistance Directory, provide products of the following manufacturers as
identified below:
1. Hilti, Inc., Tulsa, Oklahoma
800-879-8000/www.us.hilti.com
2. Approved equal.
2.03 MATERIALS
A. Use only firestop products that have been UL 1479 or ASTM E 814 tested for specific fire-
rated construction conditions conforming to construction assembly type, penetrating item
type, annular space requirements, and fire-rating involved for each separate instance.
B. Sealants, caulking materials, or foams for use with non-combustible items including steel
pipe, copper pipe, rigid steel conduit and electrical metallic tubing (EMT), the following
products are acceptable:
CORNELL UNIVERSITY SECTION 210580
Ithaca, New York FIRESTOPPING
122 McGRAW PLACE FIRESTOPPING 210580 - 3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
1. Hilti FS-ONE Intumescent Firestop Sealant
2. Hilti CP 604 Self-leveling Firestop Sealant
3. Hilti CP 620 Fire Foam
4. Hilti CP 606 Flexible Firestop Sealant
5. Hilti CP 601s Elastomeric Firestop Sealant
PART 3 - EXECUTION
3.01 PREPARATION
A. Verification of Conditions: Examine areas and conditions under which work is to be
performed and identify conditions detrimental to proper or timely completion.
1. Verify penetrations are properly sized and in suitable condition for application of
materials.
2. Surfaces to which firestop materials will be applied shall be free of dirt, grease, oil,
rust, laitance, release agents, water repellents, and any other substances that may
affect proper adhesion.
3. Provide masking and temporary covering to prevent soiling of adjacent surfaces by
firestopping materials.
4. Comply with manufacturer's recommendations for temperature and humidity
conditions before, during and after installation of firestopping.
5. Do not proceed until unsatisfactory conditions have been corrected.
3.03 INSTALLATION
A. Regulatory Requirements: Install firestop materials in accordance with UL Fire Resistance
Directory.
B. Manufacturer's Instructions: Comply with manufacturer's instructions for installation of
through-penetration joint materials.
1. Seal all holes or voids made by penetrations to ensure an air and water resistant
seal.
2. Consult with mechanical engineer, project manager, and damper manufacturer
prior to installation of UL firestop systems that might hamper the performance of
fire dampers as it pertains to duct work.
3. Protect materials from damage on surfaces subjected to traffic.
CORNELL UNIVERSITY SECTION 210580
Ithaca, New York FIRESTOPPING
122 McGRAW PLACE FIRESTOPPING 210580 - 4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
3.04 FIELD QUALITY CONTROL
A. Examine sealed penetration areas to ensure proper installation before concealing or
enclosing areas.
B. Keep areas of work accessible until inspection by applicable code authorities.
C. Inspection of through-penetration firestopping shall be performed in accordance with
ASTM E 2174, “Standard Practice for On-Site Inspection of Installed Fire Stops” or other
recognized standard.
D. Perform under this section patching and repairing of firestopping caused by cutting or
penetrating of existing firestop systems already installed by other trades.
END OF SECTION
CORNELL UNIVERSITY SECTION 211000
Ithaca, New York FIRE PROTECTION
122 McGRAW PLACE FIRE PROTECTION 211000-1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 211000 – FIRE PROTECTION
PART 1 GENERAL
1.01 SUMMARY:
A. Inside piping, including sprinkler heads, valves, hangers and supports, sleeves, and
accessories.
B. This Contractor shall include all piping, valves and devices necessary to provide protection
system as shown in accordance with the requirements of NFPA Standard 13, Installation of
Sprinkler Systems.
1.02 CODES AND REGULATIONS
A. Contractor shall provide copies of Shop Drawings and product data to the following for
approval:
1. Ithaca Fire Department
2. Cornell Environmental Health and Safety
3. Cornell Fire Protection Engineer
4. FM Global
Contractor shall not commence with construction until all parties listed above have given
their approval.
All materials and installation work shall comply with the FM Datasheet.
B. Work shall comply with codes and laws of New York State. These include but are not
limited to:
Building Code of New York State
Fire Code of New York State
C. The design, materials, and installation shall where applicable comply minimally with the
following standards:
NFPA 13 2013
FM Global
D. Organizations that have applicable standards include:
ANSI American National Standards Institute
ASME American Society of Mechanical Engineers
ASTM American Society for Testing Materials
FM FM Global/FM Approved
CORNELL UNIVERSITY SECTION 211000
Ithaca, New York FIRE PROTECTION
122 McGRAW PLACE FIRE PROTECTION 211000-2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
OSHA Occupational Safety and Health Act
NEMA National Electrical Manufacturers Association
NFPA National Fire Protection Association
UL Underwriters Laboratories, Inc.
1.03 QUALITY ASSURANCE
A. Sprinkler equipment and installations shall be in accordance with recommendations of
Owner's Underwriters and approved by local Fire Commissioner. All components to be FM
and U.L. Listed.
B. Equipment and installation to meet requirements of NFPA 13 - Standard for the Installation
of Sprinkler Systems 2013.
1.04 SUBMITTALS
A. Submit shop drawings and product data.
B. Produce complete working drawings as defined by NFPA Standard 13 for review by local
code officials and the owners insurance company if required.
PART 2 PRODUCTS
2.01 ACCEPTABLE MANUFACTURES
A. Manufacturer and Type: Tyco or equal.
2.02 SPRINKLER HEADS
A. Temperature rating on fusible links shall suit specific hazard areas. Provide temperature
rating, response, coverage and K-factor appropriate for the location. Unless otherwise
required or noted – Ordinary temperature, ½”, 5.6 K Factor.
1. Reliable
2. Victaulic
3. Viking Corp.
4. Tyco
2.03 PIPING
A. Black Steel, UL listed, ASTM A795 Type F or S, schedule 40
B. Threaded fittings – Cast Iron Class 125, ANSI 16.4. Malleable Iron Class 300, ANSI B16.3.
PART 3 EXECUTION
3.01 INSTALLATION
CORNELL UNIVERSITY SECTION 211000
Ithaca, New York FIRE PROTECTION
122 McGRAW PLACE FIRE PROTECTION 211000-3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. Run piping concealed above furred ceilings and in joists to minimize obstructions. Expose
only heads.
B. Protect sprinkler heads against mechanical injury with standard guards.
C. Provide on wall near sprinkler valve, cabinet containing extra sprinkler heads of various
styles, quantities as required, and wrench suitable to each head type.
D. Provide 1 inch diameter nipple and 1 inch x 1/2 inch reducing fitting for each upright head.
E. Install system in accordance with NFPA 13 2013. Provide all accessories required (drains, test
connections, etc.)
CORNELL UNIVERSITY SECTION 230000
Ithaca, New York GENERAL PROVISIONS FOR MECHANICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR MECHANICAL WORK 230000 - 1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 230000 - GENERAL PROVISIONS FOR MECHANICAL WORK
PART 1 GENERAL
1.01 GENERAL PROVISIONS
A. Mechanical work can encompasses HVAC and others as defined elsewhere in the contract
documents. Provide materials and labor required for complete working systems as shown on
drawings and/or specified.
B. Coordinate with other trades. The contractor shall coordinate work with other trades to
insure the coordination of the installation of their work. Coordination includes review of
other trade drawings that may affect the work and meetings with other trades.
C. The contractor shall be experienced in the work to be performed and knowledgeable of
applicable codes and standards. The contractor is expected to provide complete work in
accordance with the drawings, specifications and generally accepted methods of
construction.
1.02 DRAWINGS AND SPECIFICATIONS
A. The plans are diagrammatic and indicate only the sizes and general arrangement of piping
and equipment; exact locations of all elements shall be determined as work progresses, in
cooperation with the work of other trades. It is not intended to show every item of work or
minor piece of equipment, but every item shall be furnished and installed without additional
remuneration as necessary to complete the system in accordance with the best practice of the
trade.
1.03 MATERIALS AND EQUIPMENT
A. Manufacturers and model numbers specified on the drawings are the standard of design with
regard to performance, capacity and physical properties.
B. Submit specific product data for equipment whether the specified manufacturer is used or a
substitute is used. Submit installation data and wiring diagrams (if applicable).
C. Unless specifically noted, the equipment specification is not intended to preclude the
substitution of material and equipment by other manufacturers. The contractor is responsible
for changes due to substitutions (electrical, capacity, support, etc.)
D. If other manufacturers are named, it does not relieve the contractor from supplying
equipment or materials that meet the design intent and from the capacity, electrical, and
physical requirements of the installation. A named alternate manufacturer does not mean that
the alternate manufacturer’s standard equipment meets the specific criteria for the project.
Named alternate manufacturers does not preclude the consideration of other manufacturers.
E. Unless modified by the drawings and specifications, install equipment as required by the
manufacturer’s instructions.
CORNELL UNIVERSITY SECTION 230000
Ithaca, New York GENERAL PROVISIONS FOR MECHANICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR MECHANICAL WORK 230000 - 2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
1.03 CODES AND REGULATIONS
A. Comply with all applicable rules and regulations of the municipal laws and ordinances and
latest revisions thereof. All work shall be done in full conformity with the requirements of
all authorities having jurisdiction. Modifications required by the above authorities will be
made without additional charges to the Owner. Where alterations to and/or deviations from
the Contract Documents are required by the authorities, report the requirements to the
Architect and secure approval before work is started.
B. Work shall comply with codes and laws of New York State. These include but are not
limited to:
Building Code of New York State
Mechanical Code of New York State
Energy Conservation Construction Code of New York State
Fuel Gas Code of New York State
Fire Code of New York State
C. The materials, and installation shall where applicable comply minimally with the following
standards:
ANSI A117.1
ASHRAE Handbooks
National Electric Code (NFPA 70)
NFPA 90A
SMACNA HVAC Metal Duct Standards
D. Organizations that have applicable standards include:
AGA American Gas Association
ANSI American National Standards Institute
ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers
ASME American Society of Mechanical Engineers
ASTM American Society for Testing Materials
NEMA National Electrical Manufacturers Association
NFPA National Fire Protection Association
OSHA Occupational Safety and Health Act
SMACNA Sheet Metal and Air-Conditioning Contractors National Association
UL Underwriters Laboratories, Inc.
1.05 EXCAVATION, TRENCHING AND BACKFILL
A. Contractors shall be responsible for excavation, trenching, backfill, and floor patching as
required for their respective trades.
1.06 RECORD DRAWINGS
CORNELL UNIVERSITY SECTION 230000
Ithaca, New York GENERAL PROVISIONS FOR MECHANICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR MECHANICAL WORK 230000 - 3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. The Contractor shall keep an accurate location record of all underground and concealed
piping, and of all changes from the original design. He is required to furnish this information
to the Owner prior to his application for final payment.
B. At completion of the project, all changes and deviations from the Contract Documents shall
be recorded by the Contractor.
1.07 OPERATION AND MAINTENANCE MANUALS
A. Unless specified differently elsewhere, provide three (3) copies of an Operation and
Maintenance (O&M) manual containing the following:
1. Copies of reviewed show drawings and product data.
2. For equipment provided: maintenance and operating instructions, parts list, wiring
diagram(s).
3. All temperature control documentation (this may be bound separately if appropriate).
4. Balance report.
5. Test reports and warranty information.
B. O&M manuals information shall be bound in new three ring binders. The binders shall be
labeled with the project name.
1.08 IDENTIFICATION
A. Provide pipe identification for all piping installed including service and direction of flow.
Provide sufficient identification throughout the facility.
B. Provide valve tags for all valves indicating service. Provide valve chart or update existing
valve chart.
C. Provide labels for all equipment installed. Labels shall be phenolic nameplates.
1.09 RENOVATIONS
A. Contractors shall verify exact existing conditions in the field and coordinate new work with these
conditions.
B. Contractors shall work with utilities and/or the building owners to find shut-off valves. Finding
these valves or providing alternative means of shut-off remains the contractors responsibility.
C. When removing materials or accessing hidden materials the contractor is responsible for
restoring surfaces to match the existing adjacent surfaces.
1.10 BALANCING
CORNELL UNIVERSITY SECTION 230000
Ithaca, New York GENERAL PROVISIONS FOR MECHANICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR MECHANICAL WORK 230000 - 4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. The environmental systems including all equipment, apparatus and distribution systems shall
be tested and balanced in accordance with the National Environmental Balancing Bureau
(NEBB) Procedural Standards for Testing Adjusting and Balancing of Environmental
Systems published by NEBB, current edition.
B. Submit balancing report. Report shall be on NEBB reporting forms.
1.11 SUPPORTS AND SEALANT
A. Provide all required support for piping, duct and equipment. Provide appropriate vibration
isolation for equipment.
B. Provide sleeves for piping through walls and floor. Provide sealant for the space between the
sleeve and the pipe for fire and smoke walls/partitions/floors, exterior walls and floors,
waterproof walls and floors.
C. Provide sealant and fire stopping for duct and piping. Sealant and fire stopping for fire rated
walls/partitions/floors shall be listed for the use.
D. Unless otherwise noted, run piping and duct as neatly and unobtrusively as possible. Where
applicable run as high as possible. Coordinate with other trades.
END OF SECTION 230000
CORNELL UNIVERSITY SECTION 230523
Ithaca, New York VALVES
122 McGRAW PLACE VALVES 230523 - 1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 230523 - VALVES
PART 1 GENERAL
1.01 SUMMARY
A. Provide valves.
1.02 SUBMITTALS
A. Submit product information. If product to be used is listed by manufacturer and Model No.
specified herein, catalog cut is not required.
B. Submit valve schedule which includes valve type for each use.
1.03 QUALITY ASSURANCE
A. Valves, pressure reducing and pressure relief devices shall conform to the specification,
regulations and requirements of all Agencies (Federal, State, and Local), codes, and
associations having jurisdiction governing construction, sizing and application and
location.
B. All materials and dimensions shall conform to applicable ANSI and ASTM standards.
PART 2 PRODUCTS
2.01 GENERAL
A. Provide valves as shown on drawings.
B. Provide valves of temperature and pressure ratings exceeding conditions under which they
will operate. (WOG - Water, Oil, Gas; SWP Steam Working Pressure).
2.02 FUEL GAS VALVES
A. Ball Valves
1. 1/2"- 3/4"; 5 psig indoor. Bronze two piece body, brass ball, screwed end, tee
handle.
Nibco GB-1, Watts GBV.
PART 3 EXECUTION
3.01 INSTALLATION
A. General
CORNELL UNIVERSITY SECTION 230523
Ithaca, New York VALVES
122 McGRAW PLACE VALVES 230523 - 2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
1. Install valves at locations as shown on drawings or specified. Provide line size
valves unless otherwise noted.
2. Install valves as per manufacturer's recommendation.
END OF SECTION 230523
CORNELL UNIVERSITY SECTION 230529
Ithaca, New York SUPPORTS
122 McGRAW PLACE SUPPORTS 230529 - 1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 230529 - SUPPORTS
PART 1 GENERAL
1.01 SUMMARY
A. Pipe hangers and supports.
B. Duct hangers and supports.
1.02 REFERENCE STANDARDS/QUALITY ASSURANCE
A. Pipe Supports: MSS SP-69, Fed. Spec. A-A-1192A.
B. Duct Hangers: SMACNA Duct Manuals.
PART 2 PRODUCTS
2.01 PIPE HANGERS AND SUPPORTS
A. Provide copper plated hangers and supports for copper piping.
B. Hangers: Pipe sizes 1/2" to 1-1/2": Steel ring/band hanger.
2.03 HANGER RODS
A. Provide galvanized steel hanger rods, threaded both ends, threaded one end, or continuous
threaded.
2.04 DUCT HANGERS AND SUPPORTS
A. Hangers: Galvanized steel band iron or rolled angle and 3/8" rods.
2.05 UPPER ATTACHMENTS
A. Beam Clamp – Malleable Iron with lock nut.
2.07 ACCEPTABLE MANUFACTURERS
A. PHD Manufacturing, Mason Industries, Anvil International.
PART 3 EXECUTION
3.01 INSERTS
A. Use inserts for suspending hangers from reinforced concrete slabs and sides of reinforced
concrete beams wherever practicable.
CORNELL UNIVERSITY SECTION 230529
Ithaca, New York SUPPORTS
122 McGRAW PLACE SUPPORTS 230529 - 2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
B. Set inserts in position in advance of concrete work. Provide reinforcement rod in concrete
for inserts carrying pipe over 4" or ducts over 6" wide.
C. Where concrete slabs form finished ceiling, finish inserts, flush with slab surface.
3.02 UPPER ATTACHMENTS
A. Provide upper attachments building steel if possible. Otherwise provide upper attachment
with capacity for three times the weight supported.
B. Provide intermediate steel where required for support of piping, supports and equipment.
3.02 PIPE HANGERS AND SUPPORTS
A. Support horizontal steel and copper piping as follows:
Distance
Nominal Pipe Between Hanger Rod
Size (in.) Support (ft.) Diameter (in.)
1/2 6 3/8
3/4 to 1-1/2 6 3/8
B. Install hangers to provide minimum 1/2" clear space between finished covering and adjacent
work.
C. Place a hanger within one foot of each horizontal elbow.
D. Use hangers which are vertically adjustable 1-1/2" minimum after piping is erected.
E. Support horizontal soil pipe near each hub, with 5' maximum spacing between hangers.
F. Support vertical piping at every other floor. Support vertical soil pipe at each floor at hub.
G. Where several pipes can be installed in parallel and at same elevation, provide multiple or
trapeze hangers.
H. Where practical, support riser piping independently of connected horizontal piping.
I. Design hangers to impede disengagement by movement of supported pipe.
END OF SECTION 230529
CORNELL UNIVERSITY SECTION 232100
Ithaca, New York PIPE AND PIPE FITTINGS
122 McGRAW PLACE PIPE AND PIPE FITTINGS 232100 - 1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 232100 - PIPE AND PIPE FITTINGS
PART 1 - GENERAL
1.01 SCOPE OF WORK
A. Furnish and install all piping systems indicated on drawings, and as specified hereinafter. The
piping runs indicated are diagrammatic and intended to show the runs, risers, etc., which are
required. It is not the intent of the plans to show each offset, which may be required due to job
conditions. Install the piping in as close conformance to the plans as possible, furnishing any
additional offsets, drops, risers, etc., which may be required.
B. This Contractor shall carefully coordinate his work with the work of other contractors so as to avoid
unnecessary changes.
C. Should Architect/Engineer's details, field conditions, change of equipment or shop drawing
information necessitate an important rearrangement, report same to Engineer before proceeding
with work and obtain written approval or revised print.
1.02 SUBMITTALS
A. Piping installations shall be approved as required by the municipality having jurisdiction over the
site of the installation.
1.03 QUALITY ASSURANCE
A. All pipe and tubing shall be new, first quality, full weight, free from defects, straight, true and
round. Each length of pipe and each fitting shall be marked or stamped with manufacturer's name.
Bundled pipe shall be properly tabbed.
B. All pipe and fittings shall conform to the latest standards of A.S.A. Code for pressure piping.
C. All products shall comply with standards for low volatile organic compound emissions.
PART 2 - PRODUCTS
2.01 STEEL PIPE AND FITTINGS
A. Steel pipe
1. 1/2"- 1-1/2" ASTM A53 Grade B Type F.
B. Screwed End Fittings
1. Standard wt. malleable iron, black, banded; standard wt. 150 WSP, ANSI B16.3.
PART 3 - EXECUTION
3.01 PIPING INSTALLATION
CORNELL UNIVERSITY SECTION 232100
Ithaca, New York PIPE AND PIPE FITTINGS
122 McGRAW PLACE PIPE AND PIPE FITTINGS 232100 - 2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. General
1. Work of this section shall start as soon as building construction permits and furnish
and insert all pipe and other hangers supports, including planning of work,
purchasing materials for prompt delivery and supply sufficient labor to complete
the work as rapidly as the progress of the building allows.
2. All measurements, distances, levels shall be verified at the building.
3. Open ends of pipes and equipment shall be properly capped during installation to
keep dirt and other foreign materials out of the system.
4. Install piping properly while allowing maximum head room and allowance for the
swing of doors and equipment.
5. Install piping with approved cold strain. Make allowance for the expansion and
contraction of piping.
6. Where furred spaces are indicated, keep pipes as close to structural members as
possible so as to require minimum furring. In the case of an exterior wall, piping
shall be installed interior to the insulation so as not to break the continuity of the
insulation membrane.
7. Unless otherwise indicated, conceal piping in building construction, i.e., above
suspended ceiling. Install and test piping so as not to cause delay to work of other
trades.
8. Provide easy and safe access to valves and other apparatus requiring operation.
Provide access panels as required.
9. Do not install any bullheaded tees.
10. Cut all pipe accurately to measurements established at building and work into place
without springing or forcing. Install all pipe so that it may expand and contract
freely without change to any other work or to itself. All pipes, after having been
cut, shall be reamed to remove burrs. All threads shall be clean cut and tapered.
All piping shall be cleaned free of pipe cutting oil prior to erection. All change in
direction shall be made with fittings, not with bent pipe, and equipment shall be
properly capped and plugged during installation to keep dirt or other foreign
materials out of the system. Install piping parallel with building surfaces and other
piping, maintaining maximum head room, properly spaced, so as to provide
clearance for covering.
11. All water connections to equipment and control valves shall have brass-ground
joint unions or flanges.
CORNELL UNIVERSITY SECTION 232100
Ithaca, New York PIPE AND PIPE FITTINGS
122 McGRAW PLACE PIPE AND PIPE FITTINGS 232100 - 3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
12. Close nipples will not be accepted. Use shoulder nipples with minimum
unthreaded portion not less than 1/2". Use extra heavy pipe where shoulder
portion is less than 1-1/2".
13. Couplings will be permitted only where full lengths of pipe do not reach objective.
Use only extra heavy couplings of same material as pipe where required.
14. Furnish and install pipe anchors where indicated on drawings and where required.
The anchors shall be constructed of heavy steel shapes, welded to pipe and secured
to concrete and/or structural steel.
15. Provide die-electric unions between all copper (brass) to steel connections. Watts
Series 3000 or equal.
B. Pipe Joints
1. Square cut and ream ends of pipe, nipples, and tubing.
2. Install a gasket for each flanged joint.
3. Use an approved teflon pipe thread tape on all screwed joints.
4. Provide the appropriate die-electric connector between dissimilar pipe joints.
5. Use grooved mechanical couplings only in accessible locations.
C. Natural and Liquefied Petroleum Gas Piping
1. Install all fuel gas piping in accordance with NFPA, National Fuel Gas Code,
American Gas Association, and local utility requirements.
2. All piping shall be pitched down to low points not less than 1" in 60 feet. Provide
drip pockets at low points. Drip pockets shall be the full size of the pipe and 6"
long.
3. All outlets including valves shall be securely plugged or capped immediately after
installation.
3.02 PIPE SLEEVE INSTALLATION
A. General
1. Set sleeves, obtain review of their locations in ample time to permit pouring of concrete or
progressing of other construction work as scheduled.
2. Sleeve Size
CORNELL UNIVERSITY SECTION 232100
Ithaca, New York PIPE AND PIPE FITTINGS
122 McGRAW PLACE PIPE AND PIPE FITTINGS 232100 - 4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
a. Inside diameter of sleeve or core drilled holes to be 1/2 inch bigger than outside
diameter of the pipe, or insulation if the pipe is to be insulated. Coordinate sleeve
size with space required by modular mechanical type seal if used.
b. The length of the sleeve in walls and partitions is to be equal to the finished
thickness of the wall or partition.
c. For floors the sleeve should be 1/2 inch longer than the thickness of the floor.
Extend the sleeve 1/2 inch above finished floor.
3. Packing of Sleeves and Core Drilled Holes
a. Pack sleeves in exterior masonry walls and waterproof walls with modular
mechanical type seal.
b. Fill space around pipes through floors and fire rated walls and partitions with a UL
listed fire sealant.
3.04 PIPE SCHEDULE
A. Natural Gas Supply (above ground), 100 psig and less.
1. 1/8"- 1-1/2"; Schedule 40 black steel pipe with screwed end fittings.
3.05 TESTING
A. Test all piping as specified below before installation of insulation and connection to
equipment. Perform test in a timely manner to allow building construction to continue.
END OF SECTION 232100
CORNELL UNIVERSITY SECTION 260000
Ithaca, New York GENERAL PROVISIONS FOR ELECTRICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR ELECTRICAL WORK 260000 -1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260000 - GENERAL PROVISIONS FOR ELECTRICAL WORK
PART 1 GENERAL
1.01 GENERAL PROVISIONS
A. Provide materials and labor required for complete working systems as shown on drawings and/or
specified.
B. Coordinate with other trades. The contractor shall coordinate work with other trades to
insure the coordination of the installation of their work. Coordination includes review of
other trade drawings that may affect the work and meetings with other trades. Do not provide
wiring to equipment supplied by other contractors or subcontractors until the actual location
and electric requirements of the equipment has been verified. The electrical contractor shall
be responsible for actively pursuing this information.
1.02 INSTALLATION AND WORKMANSHIP
A. The plans are diagrammatic and indicate only the sizes and general arrangement of piping
and equipment; exact locations of all elements shall be determined as work progresses, in
cooperation with the work of other trades. It is not intended to show every item of work or
minor piece of equipment, but every item shall be furnished and installed without additional
remuneration as necessary to complete the system in accordance with the best practice of the
trade.
B. Provide installation minimally in accordance with NECA NEIS standards. Provide installation
beyond the standards if required by the project drawings and specifications.
C. Provide wiring and equipment installation in accordance with the latest edition of NFPA 70,
National Electric Code.
D. The contractor shall be experienced in the work to be performed and familiar with applicable
codes, standards and local requirements.
1.03 CODES AND REGULATIONS
A. This Contractor shall have the electrical work inspected by an approved inspection agency
and shall pay all expenses incurred by same. At the completion of the work, the Contractor
shall furnish a certificate of inspection indicating full approval of the work furnished and
installed in this Contract.
B. Work shall comply with codes and laws of New York State. These include but are not
limited to:
Building Code of New York State
Fire Code of New York State
CORNELL UNIVERSITY SECTION 260000
Ithaca, New York GENERAL PROVISIONS FOR ELECTRICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR ELECTRICAL WORK 260000 -2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
C. The materials, and installation shall where applicable comply minimally with the following
standards:
ANSI A117.1
ANSI A17.1 – Safety Code for Elevators and Escalators
Power company standards and regulations.
National Fire Alarm Code (NFPA 72)
National Electric Code (NFPA 70)
D. Organizations that have applicable standards include:
ANSI American National Standards Institute
ASME American Society of Mechanical Engineers
ASTM American Society for Testing Materials
FM FM Global/FM Approvals
ICEA Insulated Cable Engineers Association
IEEE Institute of Electrical and Electronic Engineers
OSHA Occupational Safety and Health Act
NECA National Electrical Contractors association
NEMA National Electrical Manufacturers Association
NESC National Electrical Safety Code
NFPA National Fire Protection Association
UL Underwriters Laboratories, Inc.
E. Comply with all applicable rules and regulations of the municipal laws and ordinances and
latest revisions thereof. All work shall be done in full conformity with the requirements of
all authorities having jurisdiction. Modifications required by the above authorities will be
made without additional charges to the Owner. Where alterations to and/or deviations from
the Contract Documents are required by the authorities, report the requirements to the
Architect and secure approval before work is started.
F. Furnish and file with the proper authorities, all drawings required by them in connection with
the work. Obtain all permits, licenses, and inspections and pay all legal and proper fees and
charges in this connection.
G. Should any work shown or specified be of lighter or smaller material than Code requires,
same shall be executed in strict accordance with the regulations.
H. Heavier or larger size material than Code requires shall be furnished and installed, if required
by the Plans and Specifications.
I. Equipment and components parts thereof shall bear manufacturer's name- plate, giving
manufacturer's name, size, type and model number or serial number, electrical characteristic
to facilitate maintenance and replacements. Name plates of distributors or contractors are
not acceptable.
J. Owner will stop any work or use of any material that is not being properly installed and each
Contractor shall remove all materials delivered, or work erected, which does not comply with
CORNELL UNIVERSITY SECTION 260000
Ithaca, New York GENERAL PROVISIONS FOR ELECTRICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR ELECTRICAL WORK 260000 -3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
Contract Drawings and Specifications, and replace with proper materials, or correct such
work as directed by the Owner, at no additional cost to Owner.
K. If equipment or materials are installed before proper approvals have been obtained, each
Contractor shall be liable for their removal and replacement including work of other trades
affected by such work, at no additional cost to Owner, if such items do not meet intent of the
Drawings and Specifications.
1.05 MATERIALS AND EQUIPMENT
A. Manufacturers and model numbers specified on the drawings are the standard of design with
regard to performance, capacity and physical properties.
B. Submit specific product data for equipment whether the specified manufacturer is used or a
substitute is used. Submit installation data and wiring diagrams (if applicable).
C. Unless specifically noted, the equipment specification is not intended to preclude the
substitution of material and equipment by other manufacturers. The contractor is responsible
for changes due to substitutions (capacity, support, etc.)
D. If other manufacturers are named, it does not relieve the contractor from supplying
equipment or materials that meet the design intent and from the capacity, and physical
requirements of the installation.
1.06 AS-BUILT DRAWINGS
A. The Electrical Contractor shall keep an accurate location record of all underground and
concealed piping, and of all changes from the original design. He is required to furnish this
information to the Owner prior to his application for final payment.
B. At completion of the project, all changes and deviations from the Contract Documents shall
be recorded by the Contractor.
C. Three (3) corrected sets of all operating and maintenance instructions and complete parts
lists bound in hard covers shall be furnished to the Owner.
1.07 FOUNDATIONS AND SUPPORTS
A. Provide necessary foundations, supports, pads, bases, required for equipment, conduit,
lighting fixtures, panels, racks, etc. If not specified provide support in accordance with
generally excepted construction practice.
B. For equipment where foundations are indicated or required, provide 4 inch high concrete
pads, extending 6 inches beyond equipment base in all directions, with top edge chamfered.
B. Where equipment is indicated or required to be floor-mounted on stands or legs, construct of
structural steel members or steel pipe, fittings; brace, fasten with flanges bolted to floor.
CORNELL UNIVERSITY SECTION 260000
Ithaca, New York GENERAL PROVISIONS FOR ELECTRICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR ELECTRICAL WORK 260000 -4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
C. Where ceilings or wall mounting is indicated or required, use suspended platform, brackets
or shelf, whichever is most suitable for equipment, its location. Construct of structural steel
members, steel plates, rods, as required; brace, fasten to building structure or to inserts as
reviewed.
A. Design, construct supporting structures of strength to safely withstand stress to which the
may be subjected, to distribute load, impact properly over building areas. Conform to
applicable technical societies' standards, also to codes, regulations of agencies having
jurisdiction.
D. Paint steel work with one (1) prime coat for interior locations (exception – galvanized steel
or steel with factory finish, threaded rods in unfinished locations).
1.08 CLEANING CONDUIT, EQUIPMENT
A. Conduit, equipment: thoroughly cleaned of dirt, cuttings, other foreign substances. Should
any conduit, other part of systems be stopped by any foreign matter, disconnect, clean
wherever necessary for purpose of locating, removing obstructions. Repair work damaged in
course of removing obstructions.
1.09 BONDING
A. All electrical systems must be bonded and grounded in accordance with provisions of the
National Electric Code. Provide all required accessories.
1.10 IDENTIFICATION
A. Provide typed directories for all new panelboards. Panelboards shall be labeled with designation
and voltage.
B. Update existing panelboard directories if new connections are made.
C. Provide identification for all panelboards, switchgear, transformers, switches and similar
equipment. Provide aluminum tags riveted to the enclosure or phenolic frameplates.
1.11 RENOVATIONS
A. Contractors shall verify exact existing conditions in the field and coordinate new work with these
conditions.
B. Contractors shall work with utilities and/or the building owners to find circuits. Finding these
circuits remains the contractor’s responsibility.
C. Contractor responsible for proper disposal of all materials removed (ballasts, etc.).
1.12 SUPPORTS AND SEALANT
A. Provide all required support for wiring, conduit and equipment.
CORNELL UNIVERSITY SECTION 260000
Ithaca, New York GENERAL PROVISIONS FOR ELECTRICAL WORK
122 McGRAW PLACE GENERAL PROVISIONS FOR ELECTRICAL WORK 260000 -5
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
B. Provide sleeves for penetrations of walls and floors. Provide sealant for the space between
the sleeve and the pipe for fire and smoke walls/partitions/floors, exterior walls and floors,
waterproof walls and floors.
C. Provide sealant and fire stopping. Sealant and fire stopping for fire rated
walls/partitions/floors shall be listed for the use.
D. Unless otherwise noted, run conduit as neatly and unobtrusively as possible. Where
applicable run as high as possible. Coordinate with other trades.
END OF SECTION 260000
CORNELL UNIVERSITY SECTION 260519
Ithaca, New York WIRE AND CABLE
122 McGRAW PLACE WIRE AND CABLE 260519 -1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260519 - WIRE AND CABLE
PART 1 GENERAL
1.01 SUMMARY
A. Section includes wiring, cables and connectors for power, lighting, signal, control and related
systems rated 600 volts and less.
1.02 QUALITY ASSURANCE
A. Comply with NEC requirements as to installation, materials and color coding.
B. Provide products which are UL listed and labeled.
PART 2 PRODUCTS
2.01 INSULATED CONDUCTORS
A. Conductors: Annealed uncoated copper or annealed coated copper in conformance with the
applicable standards for the type of insulation to be applied on the conductor. Conductor
sizes No. 12 and larger shall be stranded. ASTM B-3, ASTM B-174, ASTM B-8, UL-62.
B. Acceptable Manufacturers: American Insulated Wire Corp.; Southwire Co
C. Types:
1. XHHW: Moisture and heat resistant cross-linked polyethylene insulation rated 600V
conforming to U.L. requirements for type XHHW insulation (75 degrees C wet and 90
degrees C dry).
2. THWN-2: Polyvinylchloride insulation rated 600V with nylon jacket conforming to
U.L. requirements for type THWN-2 insulation (90 degrees C).
3. THHN: Polyvinylchloride insulation rated 600V with nylon jacket conforming to
U.L. requirements for type THHN insulation (90 degrees C).
2.02 CONNECTORS
A. General: Provide UL type factory fabricated, metal connectors of sizes, capacity ratings,
materials, types and classes as required for application as determined by the wire or cable
manufacturer.
B. Cable Terminations
1. Provide cable manufacturer terminations or termination specifically manfufactured for
cable type of same or greater rating.
CORNELL UNIVERSITY SECTION 260519
Ithaca, New York WIRE AND CABLE
122 McGRAW PLACE WIRE AND CABLE 260519 -2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
2.03 TAPES
A. Insulation Tapes:
1. Vinyl Tape: ASTM D-3005 Type 2, UL 510, CSA C22.2, 3M Co. Scotch No. 88.
2. Rubber Tape: HHI-553C, MIL-I-3825B, ASTM D-4388, Type 3, 3M Co. Scotch No.
23.
B. Moisture Sealing Tape: 600V UV resistant.
C. Electrical Filler Tape: UL listed, 3M Co. Scotchfil.
D Color Coding Tape: UL 510, CSA C22.2, 3M Co. Scotch No. 35;.
E. Arc Proofing: Fire and arc proofing.
2.04 PULLING COMPOUNDS
A. UL listed.
PART 3 EXECUTION
3.01 INSTALLATION
A. Install conductors in interior raceways after the raceway system is completed and finishes in
specific work areas of the building are finished.
B. Install conductors in exterior raceways after the raceway system is completed, except where
indicated on drawings to be direct burial in earth.
C. No grease, oil, or lubricant other than pulling compound specified for each type insulation
may be used to facilitate the pulling-in of conductors.
D. Use nylon line, polyethylene line, or manila rope as pull wires when installing conductors in
aluminum or rigid non-metallic conduits.
E. Identify each conductor with its source panel name and circuit number. If circuit cables are
bundled and tie-wrapped together, the cables may be identified as a group by panel name
and circuit number. Cables shall be identified in wireways, splice boxes, and junction boxes.
3.02 CIRCUITING
A. Do not change, group or combine circuits other than as indicated on the drawings.
3.03 COMMON NEUTRAL CONDUCTOR
A. A common neutral may not be used.
CORNELL UNIVERSITY SECTION 260519
Ithaca, New York WIRE AND CABLE
122 McGRAW PLACE WIRE AND CABLE 260519 -3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
3.04 CONDUCTOR SIZE
A. Install conductors of size shown on drawings. Where size is not indicated for branch circuit
wiring, the minimum size allowed is No. 12 AWG.
1. Minimum size No. 12 for general use. At 120 volts and over 100 feet total circuit
length, minimum size No. 10.
3.05 CONNECTORS
A. Splices:
1. Dry Locations:
a. For conductors No. 8 or smaller, use spring type pressure connectors or indent
type pressure connectors with insulating jackets.
b. For conductors No. 6 AWG or larger, use uninsulated indent type pressure
connectors. Fill indentions with electrical filler tape and apply insulation tape to
provide insulation equivalent to that of the conductor.
2. Damp Locations: As specified for dry locations, except apply moisture sealing tape
over the entire insulated connection.
3. Wet Locations: Use uninsulated indent type pressure connectors and insulate with
resin splice kits or heat shrinkable splices.
B. Gutter Taps in Panelboards: Install gutter tap, fill indentions with electrical filler tape and
apply insulation tape to provide insulation equipment to that of the conductors, or insulate
with gutter tap cover.
C. Terminations:
1. For conductors No. 10 AWG or smaller, use terminals for:
a. Connecting control and signal wiring to terminal strips.
b. Connecting wiring to equipment designed for use with terminals.
2. For conductors No. 8 AWG or larger, use lugs for:
a. Connecting cables to flat bus bars.
b. Connecting cables to equipment designed for use with lugs.
3. For conductor sizes larger than terminal capacity on equipment, reduce the larger
conductor to the maximum conductor size that terminal can accommodate. Reduce
section shall not be longer than 1'. Use bolted clamp type or pressure connections
suitable for reducing connection.
3.06 COLOR CODING
CORNELL UNIVERSITY SECTION 260519
Ithaca, New York WIRE AND CABLE
122 McGRAW PLACE WIRE AND CABLE 260519 -4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. Color Code and Identification of feeders and branch circuits:
1. Install color coding tapes on feeders at terminations and at 1'0" intervals in gutters,
pullboxes and manholes. Color code as follows:
120/208 Volt
Phase A - black
Phase B - red
Phase C - blue
Neutral - white
Ground - green
2. Identify interior feeders by feeder number and size in pullboxes and gutters with
premarked self-adhesive tags.
3. Identify exterior feeders by feeder number and size in manholes with embossed
aluminum tags and attach tags to cables with non-ferrous metal wire.
4. Identify street and grounds lighting conductors by circuit number and size in
manholes, also in lighting standard bases if not connected to luminaire. Use embossed
aluminum tags and attach tags to conductors with non-ferrous metal wire.
5. Install tags so that they are easily read without moving adjacent conductor or requiring
removal of arc proofing tapes.
3.07 EQUIPMENT GROUNDING CONDUCTOR
A. Install equipment grounding conductor where specified in other sections or indicated on the
drawings.
B. Equipment grounding conductor may be bare or identified with a continuous green color
insulation. This conductor is not intended as a current carrying conductor under normal
operating circumstances.
3.08 INSULATED CONDUCTOR SCHEDULE - TYPES AND USE
A. XHHW, THWN or THHN: All wiring in dry locations (except where special type insulation
is required).
B. XHHW, or THWN: All wiring in damp locations (except where special type insulation is
required).
C. THWN: Wiring installed in existing raceway systems (except where special type insulation
is required).
D. THHN: Wiring when using fluorescent fixture body as a raceway system.
CORNELL UNIVERSITY SECTION 260519
Ithaca, New York WIRE AND CABLE
122 McGRAW PLACE WIRE AND CABLE 260519 -5
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
END OF SECTION 260519
CORNELL UNIVERSITY SECTION 260529
Ithaca, New York SUPPORTING DEVICES
122 McGRAW PLACE SUPPORTING DEVICES 260529-1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260529 - SUPPORTING DEVICES
PART 1 GENERAL
1.01 SUMMARY
A. Section includes minimum materials and methods for support of electrical conduit and
equipment.
PART 2 PRODUCTS
2.01 MATERIALS
A. Fasteners: Furnish all fasteners and hardware compatible with the materials and methods
required for attachment of supporting devices.
1. Concrete Inserts: Galvanized pressed steel plate complying with ASTM A 283; box-
type welded construction with slot designed to receive steel nut and with knockout
cover; hot-dipped galvanized in compliance with ASTM A 386.
2. Masonry Anchorage Devices: Expansion shields complying with Federal
Specification FF-S-325,
3. Toggle Bolts: Tumble-wing type, complying with Federal Specifications FF-B-588,
Type, class and style as required.
4. Nuts, Bolts, Screws, Washers:
a. General: Furnish zinc-coated fasteners, with galvanizing complying with ASTM
A 153 for exterior use or where built into exterior walls. Furnish fasteners for
the type, grade and class required for the particular installation.
B. "C" Beam Clamps: Threaded red type. Maleable iron with electroplated finish.
C. Pipe Straps: Rigid steel conduit - one hole malleable iron type clamps with galvanized
finish. EMT – two hole galvanized steel.
D. Pipe Hanger: Steel lay-in or clevis type with galvanized finish. Lightweight clamp type hangers
may be used for EMT. Angle clamps may be used to connect directly to steel.
E. Channel Support System and Accessories: Furnish 12 gage galvanized steel channel and
accessories. Provide pipe straps specifically designed for the channel support.
PART 3 EXECUTION
3.01 INSTALLATION
A. Attachment of Conduit System:
CORNELL UNIVERSITY SECTION 260529
Ithaca, New York SUPPORTING DEVICES
122 McGRAW PLACE SUPPORTING DEVICES 260529-2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
1. Wood Construction: Attach conduit to wood construction by means of pipe straps or
pipe clamps and wood screws or lag bolts.
2. Masonry Construction: Attach conduit to masonry construction by means of pipe
straps or pipe clamps and masonry anchorage devices.
3. Steel Beams: Attach conduit to steel beams by means of "C" beam clamps and
hangers.
4. Steel Decking: Support conduit from the structure where possible.
END OF SECTION 260529
CORNELL UNIVERSITY SECTION 260533
Ithaca, New York RACEWAYS, FITTINGS AND ACCESSORIES
122 McGRAW PLACE RACEWAYS, FITTINGS AND ACCESSORIES 260533-1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260533 - RACEWAYS, FITTINGS AND ACCESSORIES
PART 1 GENERAL
1.01 QUALITY ASSURANCE
A. Reference Standards: Raceways shall meet the requirements of NEMA, ANSI and
Underwriters' Laboratories, Inc.
B. Applies to exterior raceways (unless superseded by another section).
1.02 SUBMITTALS
A. Waiver of Submittals: Submittals of product data for approval are not required for products
specified by brand name if the specifically named product is provided for the Work.
PART 2 PRODUCTS
2.01 RACEWAYS
A. Steel Electrical Metallic Tubing: Galvanized on the outside and coated on the inside. ANSI
C80.3..
B. Flexible Steel Conduit: Zinc coated steel continuous strip spiral wound into interlocking
convolutions. UL 1.
C. Liquid-tight Flexible Metal Conduit: Conduit constructed of galvanized steel strip,
continuous interlocked double wrapped coat with jacket of flexible PVC. UL 360.
D. Rigid Non-Metallic Conduit: Schedule 40, 90C, UL-rated PVC conforming to UEMA-TC-2
(for below ground).
E. Metal Surface Raceway: One piece .04" steel for power use UL listed. 3/4" wide. Depth as
required. Provide fittings and boxes specifically designed for the raceway system.
2.02 FITTINGS AND ACCESSORIES
A. Connectors and Couplings:
1. Rigid and IMC Conduit: Galvanized steel threaded couplings as provided by the
conduit manufacturer or threaded three piece steel/malleable iron coupling.
2. EMT: Zinc plated steel compression type.
3. Flexible Metal Conduit: Zinc plated and chromate coated terminal connector with set
screw connection.
CORNELL UNIVERSITY SECTION 260533
Ithaca, New York RACEWAYS, FITTINGS AND ACCESSORIES
122 McGRAW PLACE RACEWAYS, FITTINGS AND ACCESSORIES 260533-2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
4. Liquid-tight Flexible Metal Conduit: Provide zinc plated and chromate coated steel,
compression type terminal connector with gasket sealing rings.
5. ½” – 1” connectors for termination at device boxes and j-boxes shall be have nylon
insulated throat.
B. Conduit Bodies: Galvanized cast-metal conduit bodies is required to meet job and NEC
requirements.
PART 3 EXECUTION
3.01 RACEWAY INSTALLATION
A. Number of Circuits in Raceway: Each raceway shall enclose one circuit unless otherwise
indicated on the drawings. Homerun conduits may contain three single pole circuits from
separate phases, however the neutrals may not be combined.
B. Conduit Size: Not smaller than 1/2" electrical trade size. Conduits size to be based on the
National Electric Code.
C. Conduit in Waterproofed Floors: Install conduit runs in waterproof floors to avoid
penetrating the waterproofing. Avoid penetration of waterproofing with conduit risers so far
as practicable.
1. Where it is necessary to puncture the waterproofing for a conduit riser, install a
standard weight steel pipe sleeve extending 1/2" above the finished floor level. Flash
the steel pipe sleeve to the waterproofing with 16 ounce copper. Construct the
flashing with a copper tube extending the full height of the sleeve, soldered to a
copper base extending 6" in all directions from the sleeve.
2. The flashing will be integrated into the waterproofing by the Construction Contractor.
Provide solid cast brass floor plates with chromium finish where pipe sleeves are
exposed in rooms.
D. Install Conduit Concealed: Install conduit for all circuit work concealed in the floors,
ceilings, walls, or partitions of the building unless otherwise indicated on the drawings. If
any portions of the conduit system cannot be installed concealed due to conditions
encountered in the building, report such conditions and await approval before proceeding.
1. Run conduit in partitions vertically.
2. Conduits installed under or in floors below grade or underground shall have conduit
threads painted with sealant before couplings are assembled. Coupling and conduit
shall then be drawn up tight to ensure water tightness.
E. Conduit Installed Exposed (areas without ceilings, to exposed panelboards, mechanical
rooms, or as noted):
1. Install vertical runs perpendicular to the floor.
CORNELL UNIVERSITY SECTION 260533
Ithaca, New York RACEWAYS, FITTINGS AND ACCESSORIES
122 McGRAW PLACE RACEWAYS, FITTINGS AND ACCESSORIES 260533-3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
2. Install runs on the ceiling perpendicular or parallel to the walls.
3. Install horizontal runs parallel to the floor.
4. Conduits installed on flat surfaces in finished spaces shall be installed directly on the
surface with straps..
5. Installation of conduit directly on the floor will not be permitted.
F. Materials in Conduit Runs: All conduits in a conduit run shall be of the same material. A
combination of steel and aluminum conduit or fittings will not be permitted.
G. Conduit Ends:
1. Arrange conduit terminations in cabinet with ends at the same level.
2. Plug ends of conduits with caps to exclude foreign material until wiring is installed.
3. Use 2 locknuts and insulated bushing on end of each conduit entering cabinet or
galvanized box (plastic bushing may be used on 1/2" & 3/4" conduit).
4. Use insulated grounding bushings on the ends of conduits which are not directly
connected to the enclosure (such as stub-ups under equipment, etc.) and bond between
bushings and enclosure with equipment grounding conductor.
5. Use insulated groundings bushings or grounding wedges on ends of conduit for
terminating and bonding equipment grounding conductors (when required) if cabinets
or boxes are not equipped with grounding/bonding screws or lugs.
J. Conduit Bends: For 1/2" and 3/4" conduits, bends may be made with manual benders. For
all conduit sizes larger than 3/4", manufactured or field fabricated offsets or bends may be
used. Make field fabricated offsets or bends with an approved hydraulic bender.
L. Metal Surface Raceway: Use metal surface raceway system of size required for a number of
wires to be installed therein.
1. Do not run raceway through walls or floors. Install a pipe sleeve, or a short length of
conduit with junction boxes or adapter fittings for raceway runs through such areas.
Run raceway along top of baseboards, care being taken to avoid telephone and other
signal wiring. Where raceway crosses chair railing or picture molding, cut flat the
chair railing or picture molding to permit the raceway to lie flat against the wall. Run
raceway around door frames and other openings. Run raceway on ceiling or walls
perpendicular to or parallel with walls and floors.
2. Secure raceway at intervals not exceeding 36".
CORNELL UNIVERSITY SECTION 260533
Ithaca, New York RACEWAYS, FITTINGS AND ACCESSORIES
122 McGRAW PLACE RACEWAYS, FITTINGS AND ACCESSORIES 260533-4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
3. Install separate equipment grounding conductor for grounding of equipment. The
raceway alone will not be considered suitable for use as an effective path to ground.
4. Outlet box covers for pendant mounted fluorescent fixtures may be omitted if the
fixture canopy is notched to receive the raceway and the canopy fits snugly against the
ceiling.
5. Where equipment is mounted on an outlet box and the equipment base is larger than
the outlet box, provide finishing collar around equipment base and outlet box or
provide finishing collar/outlet box:
a. Finishing Collar: Same finish and peripheral dimensions as the equipment base,
including provisions for mounting, slots to fit over raceway and of depth to cover
outlet box and extend back to ceiling or wall.
b. Combination Finishing Collar/Outlet Box: Same finish and peripheral
dimensions as the equipment base to be mounted thereon, gage or thickness of
metal as required by National Electrical Code, including provision for mounting
and knockouts for entrance or raceway.
3.02 MAINTENANCE FIRE RESISTANCE
A. Conduit and equipment shall be firestopped to prevent the passage of flame, smoke, fumes
and hot gases.
3.03 RACEWAY SCHEDULE - TYPES & USE
A. Steel Electrical Metallic Tubing:
1. May be installed concealed as branch circuit conduits above suspended ceilings.
2. May be installed concealed as branch circuit conduits in hollow areas in dry locations.
3. Exposed in unfinished basement areas and basement areas with-out suspended ceilings.
D. Flexible Steel Conduit: Install equipment grounding conductor in the flexible steel conduit
and bond at each box or equipment to which conduit is connected:
E. Liquidtight Flexible Metal Conduit: Install equipment grounding conductor. Bond at each
box or equipment to which conduit is connected. Use 1 to 2 feet of liquidtight flexible metal
conduit for final conduit connection to:
Motors with weather-protected or totally enclosed housings.
Equipment subject to vibration (damp and wet locations).
F. Conduit installed outdoors: Use rigid steel conduit.
G. Metal Surface Raceway: Use as exposed raceway system in finished spaces.
CORNELL UNIVERSITY SECTION 260533
Ithaca, New York RACEWAYS, FITTINGS AND ACCESSORIES
122 McGRAW PLACE RACEWAYS, FITTINGS AND ACCESSORIES 260533-5
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
END OF SECTION 260533
CORNELL UNIVERSITY SECTION 260534
Ithaca, New York DEVICE AND JUNCTION BOXES
122 McGRAW PLACE PULL AND JUNCTION BOXES 260534 -1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260534 - DEVICE AND JUNCTION BOXES
PART 1 GENERAL
1.01 SUMMARY:
A. Pull and Junction Boxes.
B. Device and Outlet Boxes.
PART 2 PRODUCTS
2.01 MATERIALS
A. Interior Dry Locations: Pressed steel, galvanized, conforming to UL Standard for outlet
boxes and fittings with galvanized steel cover or extension ring as required to comply with
NEC.
2.02 SWITCH AND RECEPTACLE BOXES - CONCEALED
A. Nominal 2” x 3”, 2-3/4” deep (or as required by the number of conductors). Knockouts.
Mounting accessories and ganged as required.
2.03 LIGHTING FIXTURE BOXES - CEILING
A. 4 inch octagon.
B. For lay-in type ceilings provide box hanger which mounts to two T-bars. Knockouts.
C. For drywall ceilings provide support from two joists.
2.04 PULL AND SPLICE BOXES - 600 VOLTS AND BELOW
A. Galvanized steel, reinforced, with removable covers secured by brass machine screws and
constructed in accordance with Requirements of UL.
B. 4” steel with knockouts and cover.
2.05 BOXES IN MASONRY
A. Pressed steel masonry box, 2-1/2” deep (or as required by the number of conductors).
Knockouts.
2.06 SWITCH AND RECEPTACLE BOXES - EXPOSED
A. 4” X 2-1/8” pressed steel box, 2-1/8” deep (or as required by the number of conductors).
Knockouts.
2.07 TELEPHONE/DATA OUTLET BOXES
CORNELL UNIVERSITY SECTION 260534
Ithaca, New York DEVICE AND JUNCTION BOXES
122 McGRAW PLACE PULL AND JUNCTION BOXES 260534 -2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
A. Same as receptacle.
PART 3 EXECUTION
3.01 GENERAL
A. Mount outlet boxes as shown on drawings and specified.
B. Coordinate outlets with construction and built-in cabinets and equipment.
C. Close unused openings in outlet boxes with knockout closers.
D. Provide blank plates on outlet boxes in which no device is installed.
E. Boxes used for light fixtures (and similar) shall be install to support the weight of the fixture.
END OF SECTION 260534
CORNELL UNIVERSITY SECTION 260580
Ithaca, New York FIRESTOPPING FOR ELECTRICAL SYSTEMS
122 McGRAW PLACE FIRESTOPPING FOR ELECTRICAL SYSTEMS 260580-1
BASEMENT RENOVATION JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 260580 - FIRESTOPPING FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL
1.01 SUMMARY
A. Provide listed firestop at penetrations of rated walls, partitions, ceilings, floors and
assemblies.
1.02 DEFINITIONS
A. Firestopping: Material or combination of materials used to retain integrity of fire-rated
construction by maintaining an effective barrier against the spread of flame, smoke, and hot
gases through penetrations in fire rated wall and floor assemblies.
1.03 REFERENCES
A. Test Requirements: ASTM E 814, "Standard Method of Fire Tests of Through Penetration
Fire Stops"
B. Test Requirements: UL 1479, “Fire Tests of Through-Penetration Firestops”
C. Underwriters Laboratories (UL) of Northbrook, IL publishes tested systems in their "FIRE
RESISTANCE DIRECTORY" that is updated annually.
1. UL Fire Resistance Directory:
a. Firestop Devices (XHJI)
b. Fire Resistance Ratings (BXRH)
c. Through-Penetration Firestop Systems (XHEZ)
d. Fill, Voids, or Cavity Material (XHHW)
e. Forming Materials (XHKU)
D. International Firestop Council Guidelines for Evaluating Firestop Systems Engineering
Judgments
E. Inspection Requirements: ASTM E 2174, “Standard Practice for On-site Inspection of
Installed Fire Stops.”
F. ASTM E 84, “Standard Test Method for Surface Burning Characteristics of Building
Materials.”
1.04 QUALITY ASSURANCE
A. A manufacturer's direct representative to be on-site during initial installation of firestop
systems to train appropriate contractor personnel in proper selection and installation
procedures. This will be done per manufacturer's written recommendations published in
their literature and drawing details.
B. Firestop System installation must meet requirements of ASTM E 814 or UL 1479 tested
assemblies that provide a fire rating equal to that of construction being penetrated.
CORNELL UNIVERSITY SECTION 260580
Ithaca, New York FIRESTOPPING FOR ELECTRICAL SYSTEMS
122 McGRAW PLACE FIRESTOPPING FOR ELECTRICAL SYSTEMS 260580-2
BASEMENT RENOVATION JUNE 11, 2018
RADON AND KITCHEN WORK
1.05 SUBMITTALS
A. Submit Product Data: Manufacturer’s specifications and technical data for each material
including the composition and limitations, documentation of UL firestop systems to be used
and manufacturer's installation instructions.
B. Submit material safety data sheets provided with product delivered to job-site.
PART 2 - PRODUCTS
2.01 FIRESTOPPING, GENERAL
A. Provide firestopping composed of components that are compatible with each other, the
substrates forming openings, and the items, if any, penetrating the firestopping under
conditions of service and application, as demonstrated by the firestopping manufacturer
based on testing and field experience.
B. Provide components for each firestopping system that are needed to install fill material.
Use only components specified by the firestopping manufacturer and approved by the
qualified testing agency for the designated fire-resistance-rated systems.
2.02 ACCEPTABLE MANUFACTURERS
A. Subject to compliance with through penetration firestop systems (XHEZ) listed in Volume
II of the UL Fire Resistance Directory, provide products of the following manufacturers as
identified below:
1. Hilti, Inc., Tulsa, Oklahoma
800-879-8000/www.us.hilti.com
2. Accepted equal.
2.03 MATERIALS
A. Use only firestop products that have been UL 1479 or ASTM E 814 tested for specific fire-
rated construction conditions conforming to construction assembly type, penetrating item
type, annular space requirements, and fire-rating involved for each separate instance.
B. Sealants, foams or caulking materials for use with non-combustible items including rigid
steel conduit and electrical metallic tubing (EMT), the following products are acceptable:
1. Hilti FS-ONE Intumescent Firestop Sealant
2. Hilti CP 620 Fire Foam
3. Hilti CP 606 Flexible Firestop Sealant
4. Hilti CP 601s Elastomeric Firestop Sealant
CORNELL UNIVERSITY SECTION 260580
Ithaca, New York FIRESTOPPING FOR ELECTRICAL SYSTEMS
122 McGRAW PLACE FIRESTOPPING FOR ELECTRICAL SYSTEMS 260580-3
BASEMENT RENOVATION JUNE 11, 2018
RADON AND KITCHEN WORK
C. Foams, intumescent sealants, or caulking materials for use with flexible cable or cable
bundles, the following products are acceptable:
1. Hilti FS-ONE Intumescent Firestop Sealant
2. Hilti CP 620 Fire Foam
3. Hilti CP 606 Flexible Firestop Sealant
4. Hilti CP 601s Elastomeric Firestop Sealant
D. Non curing, re-penetrable intumescent putty or foam materials for use with flexible cable or
cable bundles, the following products are acceptable:
1. Hilti CP 618 Firestop Putty Stick
2. Hilti CP 658T Firestop Plug
E. Wall opening protective materials for use with U.L. listed metallic and specified
nonmetallic outlet boxes, the following products are acceptable:
1. Hilti CP 617 Firestop Putty Pad
F. Provide a firestop system with a "F" Rating as determined by UL 1479 or ASTM E 814
which is equal to the time rating of construction being penetrated.
PART 3 - EXECUTION
3.01 PREPARATION
A. Verification of Conditions: Examine areas and conditions under which work is to be
performed and identify conditions detrimental to proper or timely completion.
1. Verify penetrations are properly sized and in suitable condition for application of
materials.
2. Surfaces to which firestop materials will be applied shall be free of dirt, grease, oil,
rust, laitance, release agents, water repellents, and any other substances that may
affect proper adhesion.
3. Provide masking and temporary covering to prevent soiling of adjacent surfaces by
firestopping materials.
4. Comply with manufacturer's recommendations for temperature and humidity
conditions before, during and after installation of firestopping.
5. Do not proceed until unsatisfactory conditions have been corrected.
3.03 INSTALLATION
CORNELL UNIVERSITY SECTION 260580
Ithaca, New York FIRESTOPPING FOR ELECTRICAL SYSTEMS
122 McGRAW PLACE FIRESTOPPING FOR ELECTRICAL SYSTEMS 260580-4
BASEMENT RENOVATION JUNE 11, 2018
RADON AND KITCHEN WORK
A. Regulatory Requirements: Install firestop materials in accordance with UL Fire Resistance
Directory.
B. Manufacturer's Instructions: Comply with manufacturer's instructions for installation of
through-penetration materials.
1. Seal all holes or voids made by penetrations to ensure an air and water resistant
seal.
2. Protect materials from damage on surfaces subjected to traffic.
3.04 FIELD QUALITY CONTROL
A. Examine sealed penetration areas to ensure proper installation before concealing or
enclosing areas.
B. Keep areas of work accessible until inspection by applicable code authorities.
C. Inspection of through-penetration firestopping shall be performed in accordance with
ASTM E 2174, “Standard Practice for On-Site Inspection of Installed Fire Stops” or other
recognized standard.
D. Perform under this section patching and repairing of firestopping caused by cutting or
penetrating of existing firestop systems already installed by other trades.
END OF SECTION
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-1
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
SECTION 283001 - FIRE ALARM SYSTEM - ADDRESSABLE
1 - GENERAL
1.01 SUMMARY
A. The Contractor shall furnish all equipment, materials, tools, labor, drawings and all
associated documentation necessary for a complete networked fire alarm system, ready
for operational turn-over in accordance with the requirements of the NFPA-72 and the
authorities having jurisdiction. The Contractor shall provide all devices and equipment
required by the drawings and specifications.
B. Verify existing system and provide work to extend system as shown.
1.02 SUBMITTALS
A. Submit product data.
B. Submit project specific wiring diagram.
Battery capacity calculations for each control panel and power supply.
Loading calculations showing total draw and capacity of each circuit.
C. One (1) copy of each new project fire alarm system submittal shall be sent to both the CU
FE Electrical Section, and EH&S for review and comment prior to releasing final approved
submittals to the contractor.
1.03 QUALITY ASSURANCE
A. System components proposed in this specification shall be UL listed to operate together
as a system.
B. The equipment and installation shall comply with the current provisions of the following
codes and standards:
NFPA 70 - 2014 National Electric Code®
NFPA 72 - 2013 National Fire Alarm Code®
UL 864 - Control Units for Fire Protective Signaling Systems.
Install devices in accordance with ANSI A117.1and ADA.
C. Installing contractor shall have required state and local licenses.
1.07 CONTRACTOR REQUIREMENTS
A. The Contractor providing the fire alarm and detection system shall be licensed per
Article 6 D of the New York State General Business Law.
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-2
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
B. The Contractor is required to provide a complete set of As-builts within 15 days of final
Acceptance Test.
1.08 PROJECT CLOSE OUT
A. At completion of the project, the Project Manager shall be provided a complete set of
fire alarm “As-built” drawings that includes, but not limited to the following information
prior to the closeout of the project. “As-built” information shall comply with NFPA 72
requirements, the latest edition adopted by the NYSBC in effect at the time of the
project.
1. Riser diagrams for new devices.
2 - PRODUCTS
2.01 INITIATING DEVICES
A. Analog Photoelectric Smoke Sensors, FCI Model ASD-PL2
a. Analog photoelectric sensors shall have a low profile and be capable of being set at
five sensitivity settings of “LOW, LOW MEDIUM, MEDIUM, MEDIUM HIGH, and
HIGH” levels.
b. Automatic and manual functional sensitivity and performance tests shall be possible
without the need for generating smoke. This method shall test all sensor circuitry and a
“Failed Test” indication shall display for any failed test.
c. Two LEDs providing 360-degree visibility of operating status and alarm indication
shall be provided on each sensor. The LEDs shall pulse periodically indicating that the
sensor is receiving power and communication is taking place. This feature shall be field
programmable. Upon alarm, these LEDs shall light continuously. An alarm output shall
be available for remote annunciation.
d. The system shall check the sensitivity of each sensor periodically. If a sensor alarm
threshold sensitivity has changed, due to aging and/or dust accumulation, the system
shall automatically compensate for this change (drift compensation).
e. Each sensor shall allow for the setting of two sensitivity levels. These levels may be
programmed so that when the building is occupied, a sensor will be less sensitive than
when the building is unoccupied. This feature permits sensors to be more reliable and at
the same time reduces/minimizes unwanted alarms. This feature shall also provide for
programmable weekend days, where the sensor will remain at an unoccupied sensitivity
level.
f. The sensor screen and cover assembly shall be removable for field cleaning.
B. Addressable Thermal Sensor, FCI Model ATD-L/ATD-RL2 Series
a. Addressable thermal sensors shall have a low-profile and operate on the combination
“rate-of-rise” and “fixed temperature” principles with the fixed temperature set point at
135o F. FCI Model ATD-RL2. They shall contain dual thermistor sensing circuitry for
fast response.
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-3
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
C. Manual Pull Stations
1. Manual pull stations shall be of the non-coded, double-action type.
2. Keyed, latching covers of the automatic reset type shall be provided. (Note: Keyed
locks for manual pull stations shall be keyed the same as the main control panel.)
3. Manual pull station housings and doors shall be red in color unless otherwise
approved by Cornell University EH&S (Note: Manual station and wall shall be
contrasting colors as required by NFPA 72).
D. Carbon Monoxide Detectors (CO)
1. CO detectors alert the residents with signals that sound and flash a temp 4 signal
alarm.
2. Carbon monoxide (CO) devices shall be 24 VDC detectors powered by a dedicated,
supervised circuit. Removal of the CO detector shall cause a trouble signal at the fire
alarm control panel (FACP). Activation of device shall result in a supervisory signal at
the FACP.
2.04 NOTIFICATION DEVICES
A. Audible/Visual Alarm, Visual Alarm
Audible alarm indicating appliances shall be electronic horn of metal construction with a
minimum sound pressure level output of 87 dB at 10 feet. Fire alarm horns shall be
finished in baked-on red enamel paint and be UL listed for fire alarm use.
Visual indicating devices shall be a Xenon strobe type that complies with ANSI
A117.1/ADA. These devices shall be UL listed and be capable of either ceiling or wall
mounting. Flash rate of 1-3 hz. Visible notification devices shall contain multi-candela,
field selectable setting
2.05 WIRING
A. All circuits shall be rated power limited in accordance with NEC Article 760.
B. All non-addressable initiating device circuits, 24 VDC auxiliary function circuits shall be
18 AWG minimum or per manufacturer's requirements.
All notification appliance circuit conductors shall be solid copper or bunch tinned
(bonded) stranded copper. Where stranded conductors are utilized, a maximum of 7
strands shall be permitted for No. 16 and No. 18 conductors, and a maximum of 19
strands shall be permitted for No. 14 and larger conductors.
All notification appliance circuits shall be 14 AWG minimum THHN or twisted pairs or
twisted shielded pairs or per manufacturer's requirements.
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-4
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
3 - EXECUTION
3.01 INSTALLATION
A. The manufacturer of the fire alarm equipment shall provide expert supervision of the
installation and in addition, shall furnish the necessary wiring diagrams and instructions
required to make the final alarm system installation complete.
B. Provide complete system test in the presence of and the satisfaction of the owners
representative.
3.02 WIRING
A. The Contractor shall furnish and install all wiring, raceways, pull boxes, outlets and
mounting boxes for the erection and operation of a complete fire alarm system as
specified and described in these specifications, as shown on the drawings and
recommended by the manufacturer.
B. All wiring shall be in EMT conduit.
C. All wiring shall be run concealed wherever possible.
The installation of all system circuits shall conform to the requirements of Article 760
and raceway installation to the applicable sections of Chapter 3 of NFPA 70 - 1996,
National Electrical Code. Fire alarm circuit wiring shall include all circuits described in
Section 760-1 including Fine Print Note No. 1 (FPN No. 1), and as defined by the
manufacturer's UL listing.
D. All wiring shall be of the type required by the NEC and approved by local authorities
having jurisdiction for the purpose.
E. All penetration of floor slabs and firewalls shall be fire stopped in accordance with all
local fire codes.
G. Conduit Raceway
1. All systems and system components listed to UL864 Control Units for Fire Protective
Signaling Systems maybe installed within a common conduit raceway system, in
accordance with the manufacture's recommendations. System(s)or system components
not listed to the UL864 standard shall utilize a separate conduit raceway system for each
of the sub-systems.
2. All system conduits shall be EMT, 3/4 -inch minimum. In existing finished spaces use
metal surface raceway.
3. All system conduits, which are installed in areas, which may be subject to physical
damage or weather, shall be IMC or rigid steel, 3/4 -inch minimum.
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-5
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
4. Conduits shall be sized according to the conductors contained therein. Cross sectional
area percentage fill for system conduits shall not exceed 40%.
5. All conduits, except flexible conduit whips to devices, shall be solidly attached to
building structural members, ceiling slabs or permanent walls. Conduits shall not be
attached to existing conduit, duct work, cable trays, other ceiling equipment, drop ceiling
hangers/grids or partition walls, except where necessary to connect to initiating,
notification, or auxiliary function devices.
6. All system conduits, junction boxes, pull boxes, terminal cabinets, electrical enclosures
and device back boxes shall be readily accessible for inspection, testing, service and
maintenance.
3.03 TESTING
A. All fire alarm testing shall be in accordance with National Fire Alarm Code, NFPA.
B. A letter from the Contractor certifying that the system is installed entirely in accordance
with the system manufacturer's recommendations and within the limitations of the
required listings and approvals, that all system hardware and software has been visually
inspected and functionally tested by a manufacturer's certified representative, and that
the system is in proper working order.
C. Acceptance testing:
1. Provide minimum (72) hours prior notice to EH&S and AHJ.
2. Complete and submit Program sheets to EH&S.
3. Ensure that the system is pre-tested.
4. Contractor to provide all testing equipment.
5. Smoke detectors shall be tested by smoke.
6. Rate-of-rise heat detectors shall be tested by heat.
7. Fixed temperature detectors shall be tested by shorting
3.04 CLOSEOUT
A. Operating and Instruction Manuals
Operating and instruction manuals shall be submitted prior to testing of the system. Four
(4) complete sets of operating and instruction manuals shall be delivered to the owner
upon completion.
B. “As-Built” Drawings
A complete set of reproducible “as-built” drawings showing installed wiring, color
coding, and wire tag notations for exact locations of all installed equipment, specific
interconnections between all equipment and internal wiring of the equipment shall be
delivered to the owner upon completion of the system.
C. Testing Instructions
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-6
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
Complete, accurate, step-by-step testing instructions giving recommended and required
testing frequency of all equipment, and methods for testing each individual piece of
equipment shall be delivered to the owner upon completion of the system.
D. Maintenance Instructions
Maintenance instructions shall be complete, easy to read, understandable, and shall
provide the following information:
1. Instructions for replacing any components of the system, including internal parts.
2. Instructions for periodic cleaning and adjustment of equipment with a schedule of
these
functions.
3. A complete list of all equipment and components with information as to the address
and
telephone number of both the manufacturer and local supplier of each item.
4. User operating instructions shall be provided prominently displayed on a separate
sheet
located next to the control unit in accordance with UL Standard 864.
2.11 SYSTEM IDENTIFICATION/LABELING
A. Provide lettered plates for the following equipment, components, and accessories. The plate
shall contain the equipment identification (custom panel number, area served), as well as
power circuit source and breaker number. Label shall be plastic lamicoid engraved plated
or approved equal. (Note: ALL Lettered plates shall be reviewed and approved by Cornell
University’s Environmental Health and Safety prior to installation.)
1. Supplementary Notification Appliance Circuit [SNAC] Panels
2. Remote power supplies
B. Provide computer-generated adhesive labels and install on the bases of all initiating device
and notification appliances, as well as any remote test and monitoring station. The label
shall indicate the address and must be legible from a standing position below.
1. Labeling guideline for signaling line circuit (SLC): FACP/Board – Loop/cct # - Device #
2. Labeling guideline for notification appliance circuit (NAC): FACP/Board – Loop/cct # -
Device # (where addressable)
3. Labeling guideline for initiating device circuit (IDC): Loop/cct #
C. Initiating, notification, signaling, and other fire alarm system wiring, circuits, and
conductors shall be color coded and identified by number at termination points (i.e., control
panels, remote annunciators, etc.) and splice points (i.e., junction boxes, splice boxes, etc.).
Wiring shall be consistent throughout the system with no color changes on individual loops
from the FACP.
CORNELL UNIVERSITY SECTION 283001
Ithaca, New York FIRE ALARM SYSTEM - ADDRESSABLE
122 McGRAW PLACE FIRE ALARM SYSTEM – ADDRESSABLE 283001-7
BASEMENT RENOVATIONS JUNE 11, 2018
RADON AND KITCHEN WORK
D. Junction and splice boxes containing fire alarm system wiring, circuits, and conductors
shall have red covers and be marked “FIRE ALARM” in 3/4" (three- quarter inch) white
letters.
END OF SECTION 283001